Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Maximum Reach Depth"
Filters
Commonly Searched Documents
-
11B-609.2.1 Circular cross section
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-703.2.8 Line spacing
Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
-
Water Closets and Toilet Compartments for Children's Use: ADA Standard Section 604.9
Section 604.9 covers the current ADA Standards for water closets and toilet compartments for children's use.
-
11B-201.4 Construction Support Facilities
facilities and the toilet and parking facilities serving them, an accessible route is not required between site arrival points and construction support facilities when the only means of reaching...
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The vertices of the triangle shall be located ¼ inch (6.4 mm) maximum from the edge of the circle....
-
Guest Rooms
Interior hinged doors and gates: 5 pounds (22.2 N) Maximum. 2. Sliding or folding doors: 5 pounds (22.2 N) maximum. Advisory 404.2.7 Door and Gate Hardware....
-
Curb Ramps at Marked Crossings and Vehicular Lanes
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum...
-
307 Protruding Objects
., higher than 27 inches from the floor) and below the standard head room clearance (80 inches), are limited to a 4 inch depth....
-
Summary
Summary The following report provides a brief analysis of four anthropometric dimensions which were considered relevant to the width and depth dimensions of a seating surface for wheeled...
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than the depth of the wall cavity where the wall cavity is filled with cellulose loose-fill or mineral fiber insulation; 1.3....
-
Typical Issues
Access aisle depth is at least 5 feet. 2. Access aisle length is at least 20 feet. 3....
-
Savaria Orion Limited Use/Limited Application Elevator
gallery or watch our video. 1:2 cable hydraulic drive system with gradual acceleration and deceleration, makes for a smooth ride Quiet operation from submersed pump and motor Pit depth...
-
11B-226.4 Baby changing tables
This has been generally understood to include the technical requirements for accessible routes, clear floor space, reach ranges, knee and toe space, worksurface heights, operable parts and...
-
11B-904.4.2 Forward approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided....
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground....
-
609.4 Position of Grab Bars
Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
Grab Bars
If a grab bar is provided on each step, the top of the gripping surface must be 4 inches minimum to 6 inches maximum above each step....
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
7.4.11.2 Sign Contents
signs shall include at minimum the following information: Length of the trail or trail segment Surface type Typical and minimum tread width Typical and maximum...
-
4.5.3* CARPET
The maximum pile height shall be 1/2 in (13 mm). Exposed edges of carpet shall be fastened to floor surfaces and have trim along the entire length of the exposed edge....
-
Carpet [§302.2]
The standards specify the maximum pile height (1/2” measured to the backing, cushion, or pad) and texture (level or textured loop, level cut pile, or level cut/uncut pile) and require firm...
-
11B-603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1016 mm) maximum above the finish floor or ground....
