Risers shall be 4 inches (102 mm) high minimum and 7 inches (178 mm) high maximum. Treads shall be 11 inches (279 mm) deep minimum. ...
Search Results "Maximum Dimension"
Filters
Commonly Searched Documents
-
11B-504.2 Treads and risers
-
11B-604.9.5 Flush controls
Hand operated flush controls shall comply with Sections 11B-309.2 and 11B-309.4 and shall be installed 36 inches (914 mm) maximum above the finish floor....
-
§ 37.153(c)(3)
to coordinate with other available providers of demand responsive service in the area served by the public entity to maximize the service to ADA paratransit eligible individuals to the maximum...
-
11B-239.2 Minimum number
If a course is designed with the minimum 50 percent accessible holes, designers or operators are encouraged to select holes which provide for an equivalent experience to the maximum extent...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-504.2 Treads and risers
Risers shall be 4 inches (102 mm) high minimum and 7 inches (178 mm) high maximum. Treads shall be 11 inches (279 mm) deep minimum. ...
-
11B-239.2 Minimum number
If a course is designed with the minimum 50 percent accessible holes, designers or operators are encouraged to select holes which provide for an equivalent experience to the maximum extent...
-
11B-809.2.2 Turning space
Exception: Turning space shall not be required in exterior spaces 30 inches (762 mm) maximum in depth or width. Advisory 11B-809.2.2 Turning space....
-
11B-604.6 Flush controls
Hand operated flush controls shall comply with Section 11B-309 except they shall be located 44 inches (1118 mm) maximum above the floor....
-
5.2.1.1 Transfer Surface Width Recommendations for M301
Some supported the 28-inch dimension noting there is little gain in usability by increasing the transfer surface width to 30....
-
The Target Population
For many dimensions women represent the smaller end of the distribution....
-
Pilot Rock AFT Series - End Accessible Traditional A-Frame Picnic Table - Using Recycled Plastic
Tables provide 30-1/4” table height, 17-3/4” seat height (nominal dimensions)....
-
Pilot Rock AFT Series - End Accessible Traditional A-Frame Picnic Table - Using Lumber
Tables provide 30-1/4” table height, 17-3/4” seat height (nominal dimensions)....
-
Living Earth Crafts Essex™ Pedicure Chair
manicure trays Upgraded Avonite surface options Relaxor heat and massage Wide variety of upholstery and trim color options Power drain pump Pedicure Dimensions...
-
Q2.) What are the types of “field conditions” that were anticipated where the advisory says “tolerances recognized by this provision include those for field conditions”?
Those are usually the dimensions that can safely be considered industry tolerances. ...
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
The dimensions for dome size and dome spacing are the same as in the 2004 ADA and ABA Accessibility Guidelines....
-
3.3.5 Seat Height
3.3.5 Seat Height Height dimension standards for seats prescribed in the Australian, Canadian and U.S. standards were very similar (480 mm or 18.9 in., 480 mm or 18.9 in. and 485 mm...
-
Suggested accessibility guidelines for exterior concrete surfaces
However, the ACI standards do not permit interpolation or extrapolation for dimension greater than or less than 10 feet....
-
Areas for further work
Measurement instruments Accuracy of instruments/measurement uncertainty Use of significant figures Metric conversions or dual unit standards Measurement of dimensions...
-
2004 ADA and ABA Accessibility Guidelines
The Access Board is also considering additional technical criteria based on the 2004 ADA and ABA Accessibility Guidelines for cross section dimensions and clearances around gripping surfaces...
-
Election Systems & Software ADA Sip-N-Puff - AutoMark
Product Specifications Category - Kits Color - Black Product - AutoMark Ship Weight - 2.95 Freight Dimensions - 4.5" H x 12.75" W x 13.13" D...
-
11B-404.2.7 Door and gate hardware
Operable parts of such hardware shall be 34 inches (864 mm) minimum and 44 inches (1118 mm) maximum above the finish floor or ground....
-
11B-404.2.7 Door and gate hardware
Operable parts of such hardware shall be 34 inches (864 mm) minimum and 44 inches (1118 mm) maximum above the finish floor or ground....
-
Can parking signage height be considered a "safe harbor"?
No specific height dimension given. For an older property with parking signs mounted at, say 45" inches to the bottom, are these protected by the safe harbor rule? ...
