Is the surface for the accessible route, clear ground space and turning space compliant with ASTM F1951-99 Standard Specification for Determination of Accessibility of Surface Systems Under...
Search Results "Clear Tread Width"
Commonly Searched Documents
-
Applying the Accessibility Standards to the Plan, Installation, and Maintenance of Ground Level Accessible Routes for Playgrounds
-
Resting Intervals on Trails
Ensure that the resting interval is at least 60 inches (1,525 millimeters) long and at least as wide as the widest segment of the trail tread leading into it, if the resting interval is...
-
Controls: ADA Standard Section 607.5
Section 607.5 covers the current ADA Standards bathtub controls.
-
11B-307.4.1 Guy braces
Where a guy support is used within either the width of a circulation path or 24 inches maximum outside of a circulation path, a vertical guy brace, sidewalk guy or similar device shall be...
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Where doorways have steps, the illumination shall be 1 foot-candle (11 lux) minimum for a distance of 3 feet (915 mm) measured beyond the outside edge of the doorway or bottom step tread...
-
Comparison of Single-User Toilet Room Layouts: 1A, 1B, and 1C
The size of this space is determined by the minimum width required for the water closet and lavatory between the side walls, the minimum wheelchair turning space, and the space required...
- Aluminum Swaged SG Series Pressure-Locked Grating
-
11B-607.5 Controls
Controls shall be between the bathtub rim and grab bar, and between the open side of the bathtub and the centerline of the width of the bathtub....
-
Companion Seats: ADA Standard Section 1002.4.7
Where the interior width of the amusement ride is greater than 53 inches (1345 mm), seating is provided for more than one rider, and the wheelchair is not required to be centered within...
-
11B-1002.4.7 Companion seats
Where the interior width of the amusement ride is greater than 53 inches (1346 mm), seating is provided for more than one rider, and the wheelchair is not required to be centered within...
-
Accessible Routes
Technical provisions address the width, slope, and surface of both ground level and elevated accessible routes....
-
Changes in Level at Entry to Wheelchair Spaces (M303.3)
The clear width of ramp runs would be required to be 36 inches minimum....
-
11B-705.2 Detectable directional texture
The width of the directional texture shall be equal to the width of the transit vehicle’s door opening. The depth of the texture shall not be less than 36 inches (914 mm)....
- Balco FMS-A and FMS-V Roll-Up Floor Mat
-
Boat Slips
According to the table, one slip must be accessible, with clear pier space at least 40 feet long and a minimum width of 60 inches....
- EZ-ACCESS Transitions® Angled Entry Ramp
-
Lateral grab bar use
Table 12 summarizes the average clear space required for our subjects to position their WMD to perform a transfer in each protocol in terms of width, depth, and angle of approach (Figure...
-
Circulation Paths
Objects that overhang circulation paths do not provide clear headroom....
- LaCantina Multi-slide Aluminum Sliding Door System
- LaCantina Aluminum Slider System
- Stryker Evacuation Chair 6253
-
FIGURE INDEX
Floor or Ground Space Figure 305.5 Position of Clear Floor or Ground Space Figure 305.7.1 Maneuvering Clearance in an Alcove, Forward Approach Figure 305.7.2 Maneuvering...
-
Accessibility - Flatness and Lippage
Project specifications should make clear which trade is responsible for the required alterations if the subfloor is found not to be in compliance with the flatness requirements....
-
Maneuvering Clearances: ADA Standard Section 404.2.4
Section 404.2.4 covers the current ADA Standards for maneuvering clearances at doors, doorways, and gates.