Lavatories and sinks shall comply with 606. Advisory 606.1 General. If soap and towel dispensers are provided, they must be located within the reach ranges specified in 308....
Search Results "Sink Depth"
Filters
Commonly Searched Documents
-
606.1 General
-
606.1 General
Lavatories and sinks shall comply with 606. Advisory 606.1 General. If soap and towel dispensers are provided, they must be located within the reach ranges specified in 308....
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks....
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks....
-
11B-606.1 General
Lavatories and sinks shall comply with Section 11B-606. [2010 ADAS] Advisory 606.1 General. ...
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks....
-
11B-606.1 General
Lavatories and sinks shall comply with Section 11B-606. [2010 ADAS] Advisory 606.1 General....
-
11B-606.1 General
Lavatories and sinks shall comply with Section 11B-606. Advisory 11B-606.1 General....
-
4.24.5 Clear Floor Space
A clear floor space at least 30 in by 48 in (760 mm by 1220 mm) complying with 4.2.4 shall be provided in front of a sink to allow forward approach....
-
4.24.5 CLEAR FLOOR SPACE
A clear floor space at least 30 in by 48 in (760 mm by 1220 mm) complying with 4.2.4 shall be provided in front of a sink to allow forward approach....
-
11B-809.9.4 Work surfaces
maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches (762 mm) minimum for installation of a sink...
-
Knee and Toe Clearance
Accessible lavatories and sinks must provide knee and toe clearance for a forward approach (606.2)....
-
Maximum side reach ranges. (Section-by-Section Analysis)
Reach ranges apply to a variety of building elements, including light switches, key pads, electrical outlets, fire alarm pulls, card readers, thermostats, elevator controls, pay...
-
G. Compartment Size
G. If the accessible toilet is in a stall, does the stall measure at least 60" wide and 56" deep if it is wall mounted or 59" deep if it is floor mounted to allow persons who use...
-
Side Approach and Reach
[See subsections ...]
-
Obstructed High Reach
The maximum high reach is reduced to 46” when the reach over an obstruction is deeper than 10” (to a maximum of 24”). Obstructions at side reaches are limited to a height of...
-
Kitchens, Kitchenettes, or Wet Bars [9.2.2(7)]
Kitchens, Kitchenettes, or Wet Bars [9.2.2(7)] Clear floor space for either a forward or a side approach is permitted for cabinets, counters, sinks, and appliances....
-
1133A.4.1, Item 1
Sinks and work surfaces required by Section 1133A.4 shall be designed to enable repositioning to a minimum height of 28 inches (711 mm)....
-
1133A.4.1, Item 1
Sinks and work surfaces required by Section 1133A.4 shall be designed to enable repositioning to a minimum height of 28 inches (711 mm)....
-
Dimensions for Adults and Children: ADA Standard Section 102
Section 102 of the ADA Standards covers information on the dimensions for adults and children.
-
11B-102 Dimensions for adults and children
In addition, this chapter includes technical requirements based on children’s dimensions and anthropometrics for drinking fountains, water closets, toilet compartments, lavatories and sinks...
-
American Standard Cadet 2-Handle High-Arc Bar Sink Faucet 2475F
This two-handle, centerset bar sink faucet belongs to our Cadet® Kitchen Suite and complements casual décor....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
