Depending on the width of the hallway and other circulation issues, it can be preferable to swing the entry door into the toilet room....
Search Results "Clear Width"
-
Comparison of Single-User Toilet Room Layouts: 2A, 2B, and 2C
-
2.2.2 Structural Anthropometry (i.e. Body and WhMD Dimensions)
Lateral most point, left (arm, leg, WhMD or accessory) Used to measure Occupied Width....
-
4.1 Wheeled Mobility Device Dimensions
Data on occupied device sizes is most valuable for establishing clear floor area requirements....
-
T-Shaped Space: ADA Standard Section 304.3.2
Section 304.3.2 covers the current ADA Standards for t-shaped turning space.
-
11B-405.7.3 Length
The landing clear length shall be 60 inches (1524 mm) long minimum....
-
11B-405.7.3 Length
The landing clear length shall be 60 inches (1524 mm) long minimum....
-
Length: ADA Standard Section 405.7.3
Section 405.7.3 covers the current ADA Standards for the required length of ramp landings.
-
11B-206.2.19 Pedestrian street crossings
The curb ramp (excluding any flared sides) or blended transition shall be contained wholly within the width of the pedestrian street crossing served....
-
11B-206.2.19 Pedestrian street crossings
The curb ramp (excluding any flared sides) or blended transition shall be contained wholly within the width of the pedestrian street crossing served....
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Pole-supported pedestrian traffic-control buttons shall be identified with color coding consisting of a textured horizontal yellow band 2 inches (51 mm) in width encircling the pole, and...
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Pole-supported pedestrian traffic-control buttons shall be identified with color coding consisting of a textured horizontal yellow band 2 inches (51 mm) in width encircling the pole, and...
-
11B-705.1.2.5 Blended transitions
California Building Code (CBC) Regulations for Accessibility in the Triennial Code Cycle: "Requirements for detectable warning surfaces at blended transitions have been clarified in terms of “width...
-
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302 Description: The transfer surface size standard has two components: width and depth....
-
Conclusions
Our findings support those dimensions but also suggest that the width could be reduced to 28 in. Our analysis based on static anthropometry measurements....
-
11B-1009.2.6 Footrests and armrests
The armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position....
-
11B-1009.2.6 Footrests and armrests
The armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position....
-
11B-304.3.2 T-Shaped space
Each arm of the T shall be clear of obstructions 12 inches (305 mm) minimum in each direction and the base shall be clear of obstructions 24 inches (610 mm) minimum....
-
11B-304.3.2 T-Shaped space
Each arm of the T shall be clear of obstructions 12 inches (305 mm) minimum in each direction and the base shall be clear of obstructions 24 inches (610 mm) minimum....
-
Stanley Access Technologies Dura-Care 7200 Manual Sliding Door
SPECIFICATIONS CONFIGURATIONS: 2- or 4-Panel, 2-Panel S&D, Trackless TYPICAL HEIGHT: 88" | OPTION: Taller Available TYPICAL WIDTH: 2-Panel | OPTION: 84" TO 108"; Clear Door...
-
Escalators
Escalators must have a clear width of 32 inches minimum (810.9)....
-
11B-406.6 Islands
The clear width of the accessible route at islands shall be 60 inches (1524 mm) wide minimum. Where curb ramps are provided, they shall comply with Section 11B-406....
-
Three-Point Turn
three-point turn width required by bicyclists was 287 cm (113 inches)....
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
