Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impact Performance Phase 2: Final Report REPORT PREPARED FOR: U.S ACCESS BOARD, WASHINGTON,...
Search Results "Ground Surface"
Commonly Searched Documents
-
Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impacts Performance Phase 2: Final Report
- U.S. Forest Service Accessible Picnic Table Designs - Steel Leg Picnic Table
- U.S. Forest Service Accessible Picnic Table Designs - Wood Picnic Table
- U.S. Forest Service Accessible Picnic Table Designs - Stone Leg Picnic Table
-
The Impact of Transfer Setup on the Performance of Independent Transfers: Phase I Final Report
The Impact of Transfer Setup on the Performance of Independent Transfers: Final Report REPORT PREPARED FOR: U.S. ACCESS BOARD, WASHINGTON, DC Authors: Alicia Koontz, PhD,...
-
11B-902.4.1 Clear floor or ground space
Knee and toe clearance complying with Section 11B-306 shall be provided, except that knee clearance 24 inches (610 mm) minimum above the finish floor or ground shall be permitted....
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
B. M301 Diagnostic Equipment Used by Patients in a Supine, Prone, or Side-lying Position and M302 Diagnostic Equipment Used by Patients in a Seated Position
Therefore, the Significant Changes Section addresses the transfer surface and lift compatibility requirements for M301 and M302 together....
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed transfer surface...
- Figure 810.3 Bus Shelters – Drawing from the U.S. Access Board
-
5.4.1 Transfer Support Location for M301 and M302
Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
-
Section G: Ramps
(§405.7.4) G8 If the rise of the ramp is greater than 6", are handrails provided that are between 34" and 38" above the ramp surface?...
-
EZ-ACCESS® Incline Calculator for Ramp Solutions
Measure the distance from the top step/landing to the ground (RISE). Enter the values in the form to determine your run and ramp length ♦ CAUTION!...
-
Ramps M303:3.3, 3.3.1, 3.3.2
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...
-
5.4.2 Transfer Support Length for M301 and M302
The purpose of a minimum length is to ensure that there is a minimum gripping surface available to support positioning and repositioning during a transfer....
-
Handrails [§405.8, §505]
Handrail Height and Clearance Handrail Continuity and Extensions Surface requirements and clearances facilitate a power grip along the length of handrails....
- TotTurf® Synthetic Grass: Play Spaces
-
Which transition type do users with disabilities prefer?
When a sidewalk slopes more than 2% in the direction of travel and a walk with a maximum 2% cross slope intersects it, which transition segment type provides the safest usability for...
- Pilot Rock CN-S7101A Kolorcans Round Trash Receptacle With Dome Lid
- Pilot Rock CN-S7801A Kolorcans Square Trash Receptacle With Dome Lid
- Pilot Rock Varmint Defiant Trash Can Cover
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....