Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
Search Results "Ground Surface"
Commonly Searched Documents
-
Outside Surfaces
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
-
FIGURE 11A-10A KITCHEN SPECIFICATIONS
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
-
Bathroom Do’s and Dont’s
Do. Use a floor drain that extends the length of the shower to prevent water flowing into other areas of the bathroom. This is recommended, even if the floor is sloped near the...
-
Stairway Handrails Requirements in the ADA Standards (§504)
Stairway Handrails Requirements in the ADA Standards (§504) Protruding Objects The ADA Standards address hazards posed by protruding objects, such as standpipe...
-
1133A.1 General
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
5. Ground Level PV Systems
Ground Level PV Systems Ground level PV systems will have components other than vertical supports installed less than 80 inches above the ground or floor surface....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
-
Kompan, Inc. Play Structures - ELE500003 - Ridge
Requires the Premium User plan or above. (Login or upgrade your account!)
- Figure 1007.3.2 Golf Club Reach Range Area – Drawing from the U.S. Access Board
-
Kompan, Inc. Play Structures - ELE400050 - Tower
Requires the Premium User plan or above. (Login or upgrade your account!)
- Door King Inc. 6400 In-Ground Swing Gate Operator
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and maximum...
-
M305.2.3 Height (Section-by-Section Analysis)
Board sought input from the public in question 20 of the MDE NPRM preamble, on whether a transfer support height requirement of 6 inches minimum and 19 inches maximum above the transfer surface...
-
Regulatory Impact Analysis.
rooms with in-swinging doors; stairs; elevators; location of accessible routes to stages; accessible attorney areas and witness stands; assistive listening systems; and accessible teeing grounds...
-
Stages.
Department's proposed requirements mandate an accessible (pedestrian) route that connects all accessible elements within the boundary of the golf course and facility, including teeing grounds...
- Kompan, Inc. M582 - PlayWorks Sand Play Structure
- Magnuson Group UMEA Waste Receptacles