Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
Search Results "Recreational Surfacing"
-
5.4.1 Transfer Support Location for M301 and M302
-
Section G: Ramps
(§405.7.4) G8 If the rise of the ramp is greater than 6", are handrails provided that are between 34" and 38" above the ramp surface?...
-
Ramps M303:3.3, 3.3.1, 3.3.2
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...
-
5.4.2 Transfer Support Length for M301 and M302
The purpose of a minimum length is to ensure that there is a minimum gripping surface available to support positioning and repositioning during a transfer....
-
Applying the Forest Service Outdoor Recreation Accessibility Guidelines
The first step in applying Forest Service Outdoor Recreation Accessibility Guidelines (FSORAG) is to know when and where compliance is required....
-
Handrails [§405.8, §505]
Handrail Height and Clearance Handrail Continuity and Extensions Surface requirements and clearances facilitate a power grip along the length of handrails....
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
EXHIBIT A Required Accessible Elements at QuikTrip Stores
All objects that protrude from surfaces or posts into circulation paths shall comply with ADA Standards § 4.4 and a minimum 80 inch vertical clearance shall be provided in walks, halls,...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
-
Bathroom Do’s and Dont’s
Do. Use a floor drain that extends the length of the shower to prevent water flowing into other areas of the bathroom. This is recommended, even if the floor is sloped near the...
-
Stairway Handrails Requirements in the ADA Standards (§504)
Stairway Handrails Requirements in the ADA Standards (§504) Protruding Objects The ADA Standards address hazards posed by protruding objects, such as standpipe...
-
FIGURE 11A-10A KITCHEN SPECIFICATIONS
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
234 through 243 Recreation Facilities and Play Areas
Section 234 through 243 address various types of recreation facilities, including play areas....
-
1133A.1 General
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
Clear Ground Space [1011.2]
The technical requirements include specific provisions for the size, location, surface, slope, and openings in the clear ground space....
-
Recreational Checklists
[See subsections ...]
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....