At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
Search Results "Recreational Surfacing"
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
-
Bathroom Do’s and Dont’s
Do. Use a floor drain that extends the length of the shower to prevent water flowing into other areas of the bathroom. This is recommended, even if the floor is sloped near the...
-
Stairway Handrails Requirements in the ADA Standards (§504)
Stairway Handrails Requirements in the ADA Standards (§504) Protruding Objects The ADA Standards address hazards posed by protruding objects, such as standpipe...
-
FIGURE 11A-10A KITCHEN SPECIFICATIONS
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
234 through 243 Recreation Facilities and Play Areas
Section 234 through 243 address various types of recreation facilities, including play areas....
-
1133A.1 General
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
Recreational Checklists
[See subsections ...]
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
-
Clear Ground Space [1011.2]
The technical requirements include specific provisions for the size, location, surface, slope, and openings in the clear ground space....
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and maximum...
-
Conditions for Exceptions
[See subsections ...]
-
1019.1 General
This section lists the conditions for the exceptions to specific provisions in 1011, 1013, 1014, 1015, 1016, 1017, and 1018. When an entity determines that any of the following...
-
M305.2.3 Height (Section-by-Section Analysis)
Board sought input from the public in question 20 of the MDE NPRM preamble, on whether a transfer support height requirement of 6 inches minimum and 19 inches maximum above the transfer surface...
-
Certain Sports/ Recreation and Other Structures (§203.10 - §203.14)
Certain Sports/ Recreation and Other Structures (§203.10 - §203.14) These structures and spaces are also exempt: raised structures used solely for refereeing, judging, or...
-
M305.2.1 Location (Section-by-Section Analysis)
surface depths of greater than 24 inches....
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer gripping surface should be located within the minimum and maximum heights....
-
d. Unobstructed Transfer
The MDE NPRM proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they could be repositioned...