Product Features and Benefits 42″ long, 1 1/2″ wide Concealed mounting - mounting hardware included 3″ diameter flanges 1 1/2″ wall clearance Limited Faucet and Finish Warranty...
Search Results "Vertical Clearance"
-
Delta 1-1/2″ x 42″ ADA Grab Bar Concealed Mounting 40142-SS
-
Bobrick TrimLineSeries Countertop Mounted Paper Towel Dispenser B-526
Unit 12 ¾" W, 6" front to back depth (325 x 150mm); 17" (430mm) min. clearance below mounting surface is required....
-
Boolee Voting Booth
All side panel fabric is 300 x 300 urethane-coated polyester Design Specifications All weights and measures subject to minor variations Height: 60: Depth: 24” Width: 34" Clearance...
-
603 Toilet and Bathing Rooms
Doors are not permitted to swing into clear floor space or clearance required for any fixture except under certain conditions (603.2.3)....
-
4.31.2 CLEAR FLOOR OR GROUND SPACE
Figure 44 Mounting Heights and Clearances for Telephones...
-
EZ-ACCESS Transitions® Angled Entry Ramp
The Transitions Angled Entry Ramp – is a portable, stand-alone threshold ramp featuring independently adjustable legs with swivel feet, allowing for vertical adjustment ranging from 1-3/...
-
Yale 1500 Series Traditional Exit Devices
Features Available in rim, mortise, surface vertical rod and concealed vertical rod configurations Certified ANSI/BHMA A156.3, Grade 1....
-
Lavatories Adjacent to Partitions
Per 11B-606.2, we know that a clear space positioned for a forward approach is required (with exceptions), with proper knee and toe clearance. ...
-
Pilot Rock CN-TR-52 Tilting Trash Receptacle
The basket can be locked in the vertical, collection position or tilted to a 60-degree angle for unloading. ...
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
608.2.1 Transfer Type Shower Compartments
Clearance of 36 inches (915 mm) wide minimum by 48 inches (1220 mm) long minimum measured from the control wall shall be provided....
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
Portable Units [4.1.2(6)]
Where ramps are provided, it is important that required door clearances are available at the required level landing....
-
Transfer Devices for Use with Amusement Rides: ADA Standard Section 1002.6
Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm)....
-
11B-206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility. ◼...
-
11B-1002.6 Transfer devices for use with amusement rides
Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm). ◼...
-
11B-206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility. ◼...
-
11B-1002.6 Transfer devices for use with amusement rides
Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm). ◼...
-
11B-810.2.3 Connection
shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped at 35 degrees maximum from vertical...
-
Handrail Extensions
Other specifications regarding vertical supports are not addressed by ADDAG, but may be addressed in local building codes....
-
303.3 Beveled
A change in level of 1/2 inch (13 mm) is permitted to be 1/4 inch (6.4 mm) vertical plus 1/4 inch (6.4 mm) beveled....
-
704.2 Projections
extend beyond the distance determined by the following two methods, whichever results in the lesser projection: A point one-third the distance to the property line from an assumed vertical...
