Request interpreters with platform-interpreting experience for this type of meeting....
Search Results "Platform Edge"
Filters
Commonly Searched Documents
-
Considerations When Hiring an Interpreter
-
Paths to Employment Resource Center
Paths to Employment Resource Center (PERC) provides access to training and resources to promote employment and full community participation for people with disabilities through cutting-edge...
-
Eliason Corporation FP-ALU5R Heavy Duty Aluminum Mid-Panel Door
Notice: Exit device trims and levers may overlap the edge of the glazing area. Green Guard: YES, Certified for Low Emitting Products for Children and Schools and Indoor Air Quality....
-
Hager Companies Five Knuckle - Full Mortise Swing Clear Hinge BB1260
Five Knuckle - Full Mortise Swing Clear Hinge BB1260 - Ball Bearing - Standard Weight Description: - ANSI A8122 - For square edge doors - Non-rising removable pin with...
-
11B-221.6 Semi-ambulant seats
wheelchair spaces and companion seats around that field of play or performance area; (3) Wheelchair spaces and companion seats are not located on (or obstructed by) temporary platforms...
-
11B-221.6 Semi-ambulant seats
wheelchair spaces and companion seats around that field of play or performance area; (3) Wheelchair spaces and companion seats are not located on (or obstructed by) temporary platforms...
-
11B-221.6 Semi-ambulant seats
disperse wheelchair spaces and companion seats around that field of play or performance area; 3) Wheelchair spaces and companion seats are not located on (or obstructed by) temporary platforms...
-
Technical Memorandum TM 2012-07 Press Boxes
In addition, it shall include filming platforms and observation decks when access to these areas is provided by stairs instead of ladders. 2. Square Feet....
-
QUESTION: MUST RAILROADS SUBMIT PLANS FOR MEETING THE PERFORMANCE STANDARD OF SECTION 37.42 ON A STATION-BY-STATION BASIS?
Plans for meeting the performance standard at new or altered stations where track adjacent to the platform is shared with freight traffic must be submitted on a station-by-station basis....
-
408.4.1 Car Dimensions and Doors
Existing elevator cars shall be permitted to provide a clear width 36 inches (915 mm) minimum, clear depth 54 inches (1370 mm) minimum, and a net clear platform area 15 square feet (1.4...
-
Other Sources
Access Board used anthropometric data and other standards for the width of transfer surfaces on diagnostic equipment used by patients in a seated position (see M302.2.2), height of breast platforms...
-
11B-805.6 Hand washing fixtures, lavatories and sinks
686 mm) high minimum above the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge...
-
1134A.5 Bathtubs
The edge of the clear floor space shall be flush with the control wall surface....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
686 mm) high minimum above the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge...
-
AJW Architectural Products U648 Series C-fold/Multifold Towel Dispenser & Waste Receptacle Combination w/ Extended Waste - Recessed
Dispenser: Dispensing area has hemmed edges to prevent injury and towel tearing. Removable Extended Waste: Fabricated of #22 ga....
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
R302.7.1 Vertical Alignment
Where pedestrian access routes cross rails at grade, the pedestrian access route surface shall be level and flush with the top of rail at the outer edges of the rails, and the surface between...
-
404.2.10 Door and Gate Surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
Public Education
The Supervisor shall make a demonstration Edge machine available to the public several months prior to each Election at each of the Supervisor's Offices and by demonstrating it at least...
-
Carpet [4.5.3]
Trim is required along the full length of any exposed edges. This helps keep carpet from curling which can pose a tripping hazard and make wheelchair traffic difficult....
-
Clearance in Base (M301.4.1 and M302.4.1)
M301.4.1 and M302.4.1 would require the clearance in the base to be 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge...
-
Bobrick Angle-Frame Two Position Tilt Mirror B-294 1630
Beveled edges of frame hug mirror; provides gapless fit for improved appearance, and safety when cleaning mirror....
-
Toilet Buildings and Pit Toilets
Design Tip Edge protection may be used for inclines in outdoor recreation environments....
