Changes made to this section include: clarification of provisions for benches concerning clear floor or ground space (903.2), back support (903.4), and height (903.5) addition...
Search Results "Closer Height"
-
Chapter 9: Built-In Elements
-
M303.2.6 Edge Protection (Section-by-Section Analysis)
(Significant Changes – Edge Protection), the final rule requires platforms with wheelchair spaces that are raised more than 1½ inches in height to provide a minimum 2-inch-high edge protection...
-
Handrail Extensions
Handrail Extensions ADAAG addresses handrail height, diameter, and extensions provided to the end of the gangway....
-
Amusement Ride Seats Designed for Transfer
Both the clear space and the height of the seat are critical for a safe and independent transfer....
-
Tent Pads and Tent Platforms [1013]
Tent platforms must also comply with the technical requirements for height....
-
F. Check-In Areas
If a permanent reception counter is used for check in, make sure to provide a writing surface at an accessible height for people who use a wheelchair, scooter, or other mobility device....
-
4.6.1 General
Telescopes or periscopes at different heights can be mounted separately or on a single pedestal. Exception....
-
1013.1 General
The technical requirements address the clear ground space around tent pads and tent platforms (1013.2); the slope of tent pads, tent platforms, and clear ground spaces (1013.2); and the height...
-
Signs [ADA Standards §216, §703]
Visual criteria address the height, style, proportion, and spacing of characters, as well as finish and contrast, line spacing, and other features (§703.5)....
-
11B-208.2 Minimum number
For example, accessible spaces required for outlying parking facilities may be located in a parking facility closer to an accessible entrance....
-
Issue 3: Which signal? Speech WALK messages necessary
With two APS located closer than five feet to each other, it is impossible to distinguish which one is sounding based on the location and direction of the sound....
-
Location
Devices must be located a minimum of 3m (10 feet) apart, no more than 3m (10 feet) maximum from the curb line (and closer, if possible), and between the curb ramp landing and the outside...
-
Opening Force [§404.2.9]
Otherwise, closers should be calibrated with the least force necessary for closure to minimize the opening force. ...
-
11B-208.2 Minimum number
For example, accessible spaces required for outlying parking facilities may be located in a parking facility closer to an accessible entrance....
-
Pilot Rock Varmint Defiant Trash Can Cover Test
This Cover keeps trash out of reach and puts the door at a comfortable height for depositing trash....
-
Adjustable gap protocol
One was a 41 year old men that had a traumatic brain injury and double lower knee amputation, weighted 192 lbs, did not report his height, and had been using a manual wheelchair for twenty...
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
810.5.3 Platform and Vehicle Floor Coordination
The height and position of a platform must be coordinated with the floor of the vehicles it serves to minimize the vertical and horizontal gaps, in accordance with the ADA Accessibility...
-
1010.2.12.1 Delayed egress locking system
Sign lettering shall be at least 1 inch (25 mm) in height and shall have a stroke of not less than 1/8 inch (3.2 mm). 6.4....
-
11B-404.2.10 Door and gate surfaces
stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch (254 mm) bottom smooth surface height...
-
1010.2.13.1 Delayed egress locking system
Sign lettering shall be at least 1 inch (25 mm) in height and shall have a stroke of not less than 1/8 inch (3.2 mm). 6.4....
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
11B-703.3.1 Dimensions and capitalization
dots in the same cell1 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells1 0.300 (7.6 mm) Dot height...
