Handrail gripping surfaces shall extend beyond and in the same direction of ramp runs and stair flights in accordance with R409.10....
Search Results "Ramp Slope"
Filters
Commonly Searched Documents
-
R409.10 Handrail Extensions
-
§ 38.25(c) Door height
For vehicles in excess of 22 feet in length, the overhead clearance between the top of the door opening and the raised lift platform, or highest point of a ramp, shall be a minimum of 68...
-
Edge Protection
ADAAG addresses drop-offs along ramps and ramp landings but not along other portions of accessible routes or circulation paths....
-
1007.3.1 Start of Play
A clear floor or ground space 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum with slopes not steeper than 1:48 shall be provided at the start of play....
-
Carpenter's levels
To determine angles the level must be used with a measuring tape to determine slope....
-
11B-405.9.1 Reserved
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
Typical Issues
Curb ramp connects access aisle to the accessible route to the accessible entrance of the polling place. The access aisle may be at the street level or at sidewalk level....
-
11B-405.9.1 Reserved
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
4.3.8 Changes in Levels
If an accessible route has changes in level greater than 1/2 in (13 mm), then a curb ramp, ramp, elevator, or platform lift (as permitted in 4.1.3 and 4.1.6) shall be provided that complies...
-
11B-405.9.1 Reserved.
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
Trailhead Signs
pedestrians, the final rule requires the signs to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and maximum running slope...
-
1014.2.1 Transfer Access
The surface of the clear ground space is required to be firm and stable, and to slope not steeper than 1:48 in any direction....
-
1010.1.4 Floor elevation
Landings shall be level except for exterior landings, which are permitted to have a slope not to exceed 0.25 unit vertical in 12 units horizontal (2-percent slope)....
-
RESULTS OF OBJECTIVE SURFACE MEASUREMENT
The work to negotiate a ramp was linearly related to the angle of the ramp....
-
D5
[ADA Standards §§ 4.1.6(3)(d)(ii), 4.13.8] Yes No If No, replace threshold with one with beveled sides or add a sloped insert....
-
M5
[ADA Standards §§ 4.1.6(3)(d)(ii); 4.13.8] Yes No If No, replace threshold with one with beveled sides or add a sloped insert....
-
R310.3 Access Aisle
Curb ramps or blended transitions complying with R304 shall connect the access aisle to the pedestrian access route. Curb ramps are not permitted within the access aisle....
-
R305.1.3 Contrast
Visual contrast may be provided on the full surface of the curb ramp but should not extend to flared sides....
-
Findings
Within 12 months of installation, playground sites in the sample with the loose fill EWF were found to have the greatest number of deficiencies, such as excessive running slope, cross slope...
-
Behavioral Safety Products #FV600 Ligature Resistant Flush Valve Cover
It has a sloped top with rounded edges and corners and can be easily field cut to fit varying flush valve dimensions....
-
4(4)
Thresholds and changes in level at these locations are beveled with a slope no greater than 1:2....
-
H5
[ADA Standards §§ 4.1.6(3)(d)(ii), 4.13.8] Yes No NA If No, replace threshold with one with beveled sides or add a sloped insert....
-
11B-608.9 Shower floor or ground surface
Floor or ground surfaces of showers shall comply with Section 11B-302.1 and shall be sloped 1:48 maximum in any direction....
-
D5. Raised Threshold
[ADA Stds 4.1.6(3)(d)(ii), 4.13.8] Yes _____ No _____ If No, replace threshold with one with beveled sides or add sloped insert to threshold....
