[ADA Title III] §36.308 Seating in assembly areas. ...
Search Results "Recessed Seat Cover Dispenser"
-
11B-221.2.1.6 Specialty seating areas
-
11B-221.2.1.6 Specialty seating areas
[ADA Title III] §36.308 Seating in assembly areas. ...
-
Master Strategy and the Retooling of the ADA
Drafters of S. 933, however, dispensed with the idea of wholesale retrofitting. Instead they required that all new construction be accessible....
- Access Board: Standard Roll In Shower Stalls
-
General Seating: ADA Standard Section 221.2.1.1
Section 221.2.1.1 covers scoping requirements in the current ADA Standards for general seating in assembly areas.
-
Appendix 2- Photos of Participants in the IDEA Center Research
Appendix 2- Photos of Participants in the IDEA Center Research Examples of High Seats: Examples of Very Large and Small Clear Floor Area Widths: Examples of Very Long...
- Figure 608.5.2 Standard Roll-In Type Shower Compartment Control Location – Drawing from the U.S. Access Board
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space....
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space....
-
Guidelines for Requirement 6
Guidelines provide that a powder room is subject to the requirement for reinforced walls for grab bars when the powder room is the only toilet facility located on the accessible level of a covered...
-
1. Who is Covered?
Not everyone is covered under the ADA. There are certain basic requirements that must be met in order to be protected....
-
(5) Reinforced walls for grab bars
The only change made to these guidelines has been to subject powder rooms to the reinforced wall requirement when the powder room is the only toilet facility on the accessible floor of a covered...
-
(2) Adjustability: Minimum Low Transfer Height
Additionally, the reports pointed to current accessibility standards for toilet seats, shower seats, and tub seats, which require a height of 17 inches minimum and 19 inches maximum....
-
5. Edge Protection
The MDE NPRM proposed edge protection on the ramps leading up to the raised platform (proposed M303.3.3.4), but did not require edge protection on the raised platforms themselves....
-
M301.2.2, M302.2.2 Transfer Size
M301.2.2, M302.2.2 Transfer Size Proposed requirement: 30" wide minimum and 15" deep minimum • Sub-Committee Recommendation: 28" wide minimum and 17" deep minimum. This...
-
§ 36.406(f) Assembly areas
(f) Assembly areas. Assembly areas subject to the proposed standards shall comply with the provisions applicable to assembly areas, including, but not limited to, sections 221 and...
-
§ 36.406(f) Assembly areas
(f) Assembly areas. Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to,...
-
§ 36.302(f)(1)
(1)
-
§ 36.302(f) Ticketing.
(f) Ticketing.
-
Miscellaneous - Areas of Sports Activities, Team or Player Seating, Exercise Machines & Equipment, Bowling Lanes, Saunas & Steam Rooms, and Shooting Facilities
Word Fillable Form (0.7MB) Word Non-Fillable Form (0.6MB) PDF Non-Fillable Form (0.6MB)
-
Requirement 6. Reinforced walls for grab bars.
Section 100.205(c)(3)(iii) requires that covered multifamily dwellings with a building entrance on an accessible route shall be designed and constructed in such a manner that all premises...
-
T215 Communication Features
With respect to signage for priority seats, the 2010 NPRM proposed that priority seats for passengers with disabilities be identified by signs informing other passengers to make such seats...
- Midmark 630 HUMANFORM™ Procedures Table