mini-high platforms, shall be coordinated with the boarding platform design such that the horizontal gap between a car at rest and the platform shall be no greater than 3 inches and the height...
Search Results "Transfer Surface Height"
-
§ 38.93(d)(1) Requirements
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
Can stair treads and risers be perforated?
Stair treads must meet requirements for floor or ground surfaces which specify that surface openings not allow passage of a sphere more than ½ inch in diameter (§302.3)....
- Pilot Rock End Accessible Multi-Pedestal Table APT Series 3"x4" Recycled Plastic
-
226.1 General
Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with 902....
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2....
-
Handrails [§504.6, §505]
Handrails [§504.6, §505] Handrails are required on both sides of stairs and must be continuous within the full length of each stair flight. Inside handrails on switchback or...
-
Clear Floor or Ground Space: ADA Standard Section 902.4.1
A clear floor space complying with 305 positioned for forward approach shall be provided. Knee and toe clearance complying with 306 shall be provided, except that knee clearance 24...
- Bosch Power Tools - GPL-3 3 Point Laser
-
11B-608.5.1 Reserved
[2010 ADAS] 608.5.1 Transfer Type Shower Compartments....
-
II. Recommendations of Diagnostic Imaging Equipment Manufacturers on Transfer Surface Low Height
transfer surface low height for the following reasons: 1....
-
Water Hydrants
The surface at the base of water hydrants at recreation areas must be firm and stable with a 60-inch turning radius. See the "Surfaces" rule of thumb above....
-
4.16.2 Clear Floor Space
However, in accommodating assisted transfers, these guidelines were less of an issue than providing space adjacent to the water closet for caregivers and including a 5’ turning radius in...
-
1132A.3, Item 1
Doors shall not be less than 6 feet 8 inches (2032 mm) in height....
-
1132A.3, Item 1
Doors shall not be less than 6 feet 8 inches (2032 mm) in height....
- Pilot Rock SQT3-4 Series Square Portable Table - Using Lumber or Recycled Plastic
- Pilot Rock End Accessible Multi-Pedestal Table APT Series
- Pilot Rock PQT3-4 Square Pedestal Table Using Lumber
- Pilot Rock PQT3-4 Square Pedestal Table Using Recycled Plastic
-
Applying the Accessibility Standards to the Plan, Installation, and Maintenance of Ground Level Accessible Routes for Playgrounds
Is the surface for the accessible route, clear ground space and turning space compliant with ASTM F1951-99 Standard Specification for Determination of Accessibility of Surface Systems Under...
-
703.5.6 Height from Finish Floor or Ground
703.5.6 Height from Finish Floor or Ground. Visual characters shall be 40 inches (1015 mm) minimum above the finish floor or ground....
-
Signage [4.6.4]
Recommendation: Since traffic codes often govern sign height, ADAAG does not specify a height for parking signs....
-
Test Procedures
indentation on each surface (Axelson and Chesney, 1999)....