Seat heights for males were typically higher than for females....
Search Results "Handrail Height"
-
Notes
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
[A] ADDITION
[DSA-AC] An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
Podium
Podium: If a podium is used, some speakers who use mobility devices may not be able to use one that is standard height....
-
Side Reach [4.2.6]
Since the height of reach decreases with depth, the maximum high reach is limited to 46 inches over obstructions no more than 24 inches deep and 34 inches high....
-
1012.3 Opening limitations
Open guards shall have balusters or ornamental patterns such that a 4-inch-diameter (102 mm) sphere cannot pass through any opening up to a height of 34 inches (864 mm)....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
ADDENDUM TO PHASE I FINAL REPORT: Points of Clarification
The Adjustable Height protocol included two types of transfers, a transfer to a higher height and a transfer to a lower height relative to the mobility device's seat to floor height....
-
405.9 Edge Protection
Edge protection shall not be required on ramps that are not required to have handrails and have sides complying with 406.3. 2....
-
Accessible Routes Adjacent to the Playing Surface
The accessible route provisions in ADAAG address slope (maximum of 1:12 or 8.33%), width (minimum of 36 inches), cross slope (maximum of 1:50 or 2%), handrails, and changes in level....
-
405.9 Edge Protection
Edge protection shall not be required on ramps that are not required to have handrails and have sides complying with 406.3. 2....
-
405.9 Edge Protection
Edge protection shall not be required on ramps that are not required to have handrails and have sides complying with 406.3. 2....
-
Q2: Milling a Road Surface
What constitutes “overlays of additional material to the road surface” with respect to milling, specifically, when a roadway surface is milled and then overlaid at the same height (i.e.,...
-
Shower Threshold
The proposed rule specified a maximum threshold height of ½ inch, provided that those greater than ¼ inch are beveled with a slope of 1:2 maximum (608.7)....
-
D. Beds in accessible guest rooms and sleeping rooms
Many individuals with disabilities have urged the Department to regulate the height of beds, particularly in accessible hotel guest rooms, and to require that such beds have clearance under...
-
2.2.3 Functional Reach
Those individuals unable to grasp and/or lift any of the cylinders above shoulder height did not complete the reaches....
-
4.4 Knee and Toe Clearances
Smaller individuals who have heavy thighs, those with high seats and scooter users also have high lap heights....
-
810 Transportation Facilities
This height allows for freight passage while reducing the height of the first step of a rail car above the platform....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 15 percent maximum of the height of the character....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
605 Urinals
Section 604.5 provides criteria for accessible urinals, including the height and depth, clear floor space, and flush controls....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....