Recommendations of Diagnostic Imaging Equipment Manufacturers on Transfer Surface Low Height The aforementioned medical diagnostic imaging equipment manufacturers support a 19 inch minimum...
Search Results "Gripping Surface"
-
II. Recommendations of Diagnostic Imaging Equipment Manufacturers on Transfer Surface Low Height
-
World Dryer SLIMdri™ Surface-Mounted Hand Dryer
Surface-Mounted ADA Compliant Hand Dryers SLIMdri™ is a high speed, energy efficient, surface-mounted and ADA compliant hand dryer....
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.5 Amusement Ride Seats Designed for Transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.5 Amusement Ride Seats Designed for Transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
AJW Architectural Products U582 1.5 Gallon Sanitary Napkin Disposal - Surface Mounted
Optional finger grip in lieu of lock is available....
-
Ground and Floor Surfaces [4.5]
[See subsections ...]
-
ADA Solutions, Inc. Radius Tactile Detectable Warning Surface
The Surface Applied Radius Tactile is used to retrofit over an existing concrete substrate and can be installed in as little as 10 minutes....
-
17. If a soil stabilizer was installed as part of the trail surface material, please indicate the product name.
If a soil stabilizer was installed as part of the trail surface material, please indicate the product name....
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
Amusement Ride Seats Designed for Transfer
When greater distances are required for transfer, consideration should be given to providing gripping surfaces, seat paddings, and avoiding sharp or protruding objects....
-
31. Please indicate the number of the complete replacements of the trail surface that you have already performed
Please indicate the number of the complete replacements of the trail surface that you have already performed (in total, so far):...
-
M305.1 General
Supports shall comply with M305.
-
M305.1 General (Section-by-Section Analysis)
This is an introductory section.
-
M305.1 General
Supports shall comply with M305, as applicable.
-
ADA Solutions, Inc. Cast in Place Tactile Surface
concrete Cast-In-Place Tiles have a 1/4" nominal thickness and feature embedment ribs 3" on center through entire length of tile Plastic sheeting protection covers entire surface...
-
Gamco Surface Mounted Hand Dryer - DR-5128
Description Surface-mounted ADA (American Disabilities Act) compliant dryer, with stainless steel with brushed finish....
-
Pilot Rock SRP Saddleback Bike Rack Surface Mount
Model SRP Saddleback Bike Racks are SURFACE mounted by means of a bolt down base plate....
-
Gamco Surface-Mounted Robe Hook Satin - 76717
Description (Formerly model 5153) Surface-mounted robe hook shall be type-304 stainless steel with satin-finish....
-
1002.5 Amusement Ride Seats Designed for Transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
Additional Technical Criteria Considered for Handrails on Ramps
These technical criteria are available at http://www.access-board.gov/ada-aba/final.cfm#a505 and address continuity, height, clearance, gripping surface, cross section, surfaces, fittings...
