The outside diameter dimension range for circular cross-section grab bars are between 1.25 and 2 inches. A 1.5 inch diameter was chosen for the study....
Search Results "Car Dimension"
-
Grab bars
-
A4.32.4 Height of Tables or Counters
34 865 Seated in a 16 in (405 mm) high chair: Manual work 26 660 27 685 Light, detailed work 28 710 31 785 1All dimensions...
-
A4.32.4 HEIGHT OF WORK SURFACES
Seated in a 16-in (405-mm)-high chair: Manual work 26 660 27 685 Light, detailed work 28 710 31 785 * All dimensions...
-
Clear Space Evaluation
The space needed by the study participants was compared to a turning space dimension as described in the ADA-ABA standards (60x60 inch space)....
-
Feature 1 - Parking and Passenger Drop-Off Areas
Those who arrive by car or van need an accessible parking space as close as possible to an accessible entrance....
-
Parking
You must provide accessible parking spaces for cars and vans if it is readily achievable to do so....
-
Scoping Requirements for Elevators
from typical elevators in that they provide a means of indicating the desired floor at the location of the call button, usually through a key pad, instead of a control panel inside the car...
-
Two-Way Communication
Section 407.4.9 provides criteria for emergency two-way communication systems in elevator cars which address the height of operable parts and identification by tactile characters....
-
11B-411.1.1 Floor designations
character such as "M2", indicating "mezzanine" and the "story number", respectively, in which it is located, provided there is no duplication with alphanumeric designations of elevator cars...
-
11B-411.1.1 Floor designations
character such as "M2", indicating "mezzanine" and the "story number", respectively, in which it is located, provided there is no duplication with alphanumeric designations of elevator cars...
-
If a passenger loading area serves cars and vans, as well as buses, must the provisions for passenger loading zones and bus loading zones both be satisfied?
No, provisions for bus loading zones (§810.2) apply only to on-street bus stops and those bus loading zones that exclusively serve designated or specified public transportation...
-
§ 37.91(e)
(e) On any train in which either a single level or bi-level dining car is used to provide food service, a person providing intercity rail service shall provide appropriate aids and services...
-
U.N. Convention on the Rights of Persons with Disabilities (CRPD)
The Convention is intended as a human rights instrument with an explicit, social development dimension....
-
III-7.2100 Equivalent facilitation
For instance -- 1) In altered areas, elevator car dimensions can be smaller than the standards would mandate for new construction (§4.1.6(3)(c)); 2) Rather than install a text telephone...
-
Transit Stops (R308.1) (Section-by-Section Analysis)
Where transit stops serve vehicles with more than one car, boarding and alighting areas serving each car must comply with these requirements....
-
Ambulatory Accessible Compartment
Throughout the new guidelines, the Board has sought to specify dimensions as a range instead of in absolute terms where practicable to facilitate compliance without compromising accessibility...
-
308.1 General
These dimensions apply to either forward or side reaches....
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
5.3.2.1 Transfer Sides Recommendation for Stretchers On stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are in the supine, prone...
-
9. Exterior Ramps
[ADA Stds. 4.8.3] Yes __ No __ N/A __ Comments: _______________________________ d. do the exterior ramps have running slopes that are 1:12 or less (critical dimension of 2" or less...
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways. ...
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
Space Allowance and Reach Ranges [4.2]
Adult dimensions and measures for standard manual wheelchairs form the basis of many ADAAG specifications....
-
505.6 Gripping Surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each 1/2 inch (13 mm) of additional handrail perimeter dimension...
-
4.4.4 Clear Floor or Ground Space
The long dimension of the clear space shall be roughly perpendicular to the length of the bench....
