To prevent causing injury or imbalance, the plumbing can be located behind walls or to the side of the toilet; or if approved by the local authority having jurisdiction, provide a toilet...
Search Results "Head End Wall"
-
604.6 Flush Controls
-
4.35.4 Bench
Every accessible dressing room shall have a 24 in by 48 in (610 mm by 1220 mm) bench fixed to the wall along the longer dimension....
-
Position and Hand physiology
Position and Hand physiology The map is mounted at a slight angle from the wall that forces your hand into an awkward position....
-
11B-609.4 Position of grab bars
The height of the lower grab bar on the back wall of a bathtub shall comply with Section 11B-607.4.1.1 or 11B-607.4.2.1....
-
M305.2.1 Location (Section-by-Section Analysis)
Therefore, the Access Board has separated the location provision into end transfer supports and side transfer supports....
-
California: Toilet Grab Bars - Uneven height allowed?
Grab bars shall be provided on the side wall closest to the water closet and on the rear wall....
-
Microsoft Word Accessibility Basics: Webinar Series Archive
6th: Page Structure - Access Webinar Resources Here A high-level overview of best practices for accessible page structure including providing a context sensitive page title, proper heading...
-
Plan 3A: 12-Foot Wide Accessible Guest Room
at fixtures and turning space overlap (section 603.2.2); • Turning space includes knee and toe clearance at lavatory (section 304.3); • Water closet clearance is 60 inches at back wall...
-
Plan 3B: 12-Foot Wide Accessible Guest Room
at fixtures and turning space overlap (section 603.2.2); • Turning space includes knee and toe clearance at lavatory (section 304.3); • Water closet clearance is 60 inches at back wall...
-
Plan 2A: 13-Foot Wide Accessible Guest Room
at fixtures and turning space overlap (section 603.2.2); • Turning space includes knee and toe clearance at lavatory (section 304.3); • Water closet clearance is 60 inches at back wall...
-
407.4.1 Car Dimensions
)(ii)] Table 407.4.1 Elevator Car Dimensions Minimum Dimensions Door Location Door Clear Width Inside Car, Side to Side Inside Car, Back Wall...
-
2. Typical Issues for Individuals Who Are Blind or Have Low Vision
Typical Issues for Individuals Who Are Blind or Have Low Vision Objects that are wall mounted, that project into a pedestrian route from the side, or that are overhead can be hazards...
-
Location and Spacing
It may be possible to serve some large rooms or corridor sections with a single appliance located on a perimeter wall or suspended below the ceiling so that the signal can spread throughout...
-
Part 2. Typical Issues for Voters Who Are Blind or Have Low Vision
Typical Issues for Voters Who Are Blind or Have Low Vision Objects that are wall-mounted, that project into a pedestrian route from the side, or that are overhead must be located so that...
-
General [4.1.6(1)]
a toilet room renovation is limited to replacement of a lavatory and reflooring, then the new lavatory and floor must comply; where the work is more extensive and also involves moving walls...
-
Section 307 Protruding Objects
This dryer protrudes more than 4" from the wall and is greater than 27" above the finish floor. Isn't this a violation of Section 307 Protruding Objects?...
-
1127B.5, Item 4
A level landing 4 feet (1219 mm) deep shall be provided at the upper end of each curb ramp over its full width to permit safe egress from the ramp surface, or the slope of the fanned or...
-
Orientation (slide 12)
You know, any time you go through [circulation areas], not when you get to the end. But as you go down the line, the waiting areas are separate....
-
16. Meetings with Class Counsel
Within six (6) months after the end of the Compliance Period, but no less than three months prior to the termination of the District Court’s jurisdiction herein, the City shall provide Class...
-
408.4.1 Car Dimensions and Doors
Car doors shall be positioned at the narrow ends of cars and shall provide 32 inches (815 mm) minimum clear width. EXCEPTIONS: 1....
-
4.4 Equipment Barriers and Solutions
Solutions Simple/Low cost Involved / High cost Spaces between the equipment are too narrow Ask staff to move one of each type of equipment to the end...
-
Construction Specification Institute
lines, measurements were to be taken in minimum 2 - foot lengths along a line running parallel to the long dimension, with one measurement line per 6 feet of length and within 2 feet of ends...
-
3. Relationship between Functional Performance Criteria and Technical Provisions
Industry commenters stated that they could not guarantee that the functional performance criteria had been met unless they controlled all the components of the end-to-end solution....
