EXCEPTION: The detainee side of cubicles or counters at non-contact visiting areas not serving holding cells required to comply with 231 shall not be required to comply with 902 or 904.4.2...
Search Results "Patient Change Area"
-
231.4.1 Cubicles and Counters
-
New and Altered Permanently Installed Amusement Rides
Such an extensive alteration to an amusement ride may well require that new load and unload areas be designed and constructed....
-
M303.2 Wheelchair Spaces
Wheelchair spaces complying with M303.2 shall be provided at diagnostic equipment.
-
M305.3.3 Fittings
Standing supports shall not rotate within their fittings.
-
M303.2.3 Depth
The depth of wheelchair spaces shall comply with M303.2.3.
-
11B-805.2.3 Turning space
Turning space complying with Section 11B-304 shall be provided within the room.
-
M302.3.3 Head and Back Support
Where the diagnostic equipment is used in a reclined position, head and back support shall be provided and shall comply with M305.5.
-
M302.2.4 Transfer Sides
Options to transfer from a mobility device shall be provided on two adjoining sides of transfer surfaces. EXCEPTION: Options to transfer to or from a mobility device onto...
-
1. MOVING (MOBILITY / PHYSICAL / MOTOR – LIMITED OR NO ABILITY GRAB, GRIP, LIFT, HOLD, ETC)
1.1. Uses Wheelchair Scooter Walker Cane Braces Prosthesis Service Animal - Overnight stay w/...
-
805.2 Turning Space
Turning space complying with 304 shall be provided within the room.
-
805.2 Turning Space
Turning space complying with 304 shall be provided within the room.
-
M303.2 Wheelchair spaces (Section-by-Section Analysis)
This is an introductory section.
-
5.2.3 Transfer Surface Measurement
5.2.3 Transfer Surface Measurement. The transfer surface should be measured from the center-point of each side of the transfer surface.
-
5.3.3.1 Transfer Sides for Exam Chairs with Fixed Footrests
5.3.3.1 Transfer Sides for Exam Chairs with Fixed Footrests. The 17 inch minimum depth and 21 inch minimum width should be located on both sides of examination chairs with a fixed...
-
805.2 Turning Space
805.2 Turning Space. Turning space complying with 304 shall be provided within the room.
-
M302.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface. Each transfer side...
-
M303.2.3 Depth
Where wheelchair spaces can be entered from the front or rear, the wheelchair space shall be 48 inches (1220 mm) deep minimum. Where wheelchair spaces can be entered only from the...
-
M302.3.3 Head and Back Support
Where the diagnostic equipment is used in a reclined position, head and back support shall be provided. Where the incline of the back support can be modified while in use, head and...
-
M303.2.2 Width
Wheelchair spaces shall be 36 inches (915 mm) wide minimum.
-
M305.3.3 Fittings
Standing supports shall not rotate within their fittings.
-
11B-805.2.3 Turning space
Turning space complying with Section 11B-304 shall be provided within the room.
-
11B-805.2.3 Turning space
Turning space complying with Section 11B-304 shall be provided within the room.
-
M303.2.6 Edge Protection (Section-by-Section Analysis)
(Significant Changes – Edge Protection), the final rule requires platforms with wheelchair spaces that are raised more than 1½ inches in height to provide a minimum 2-inch-high edge protection...
-
11B-231.4.1 Cubicles and counters
Exception: The detainee side of cubicles or counters at non-contact visiting areas not serving holding cells required to comply with Section 11B-231 shall not be required to comply with...