Search Results "Walking Surface"
-
U.S. Forest Service Accessible Picnic Table Designs - Steel Leg Picnic Table
-
U.S. Forest Service Accessible Picnic Table Designs - Wood Picnic Table
-
U.S. Forest Service Accessible Picnic Table Designs - Stone Leg Picnic Table
-
DSA Drawing 11B-406.6-10 Cut-Through Median Less Than 96 inches in Length with No Gutters (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
The Impact of Transfer Setup on the Performance of Independent Transfers: Phase I Final Report
The Impact of Transfer Setup on the Performance of Independent Transfers: Final Report REPORT PREPARED FOR: U.S. ACCESS BOARD, WASHINGTON, DC Authors: Alicia Koontz, PhD,...
-
302 Floor or Ground Surfaces
Section 302 requires floor or ground surfaces to be stable, firm, and slip resistant and provides specifications for carpets and surface openings. Comment....
-
What surface characteristics are required of an accessible route?
A slip-resistant surface provides sufficient frictional counterforce to the forces exerted in walking to permit safe ambulation....
-
B. M301 Diagnostic Equipment Used by Patients in a Supine, Prone, or Side-lying Position and M302 Diagnostic Equipment Used by Patients in a Seated Position
Therefore, the Significant Changes Section addresses the transfer surface and lift compatibility requirements for M301 and M302 together....
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed transfer surface...
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
11B-250 Circulation paths
[See subsections ...]
-
5.4.1 Transfer Support Location for M301 and M302
Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
-
Section G: Ramps
(§405.7.4) G8 If the rise of the ramp is greater than 6", are handrails provided that are between 34" and 38" above the ramp surface?...
-
Ramps M303:3.3, 3.3.1, 3.3.2
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...
-
Walk Through Procedures
Recommend that a portion of staff meetings be devoted to discuss and practice separate parts of a plan. This allows you and your colleagues to concentrate efforts on the particular...
-
TotTurf® Synthetic Grass: Play Spaces
Description Tot Turf Play Spaces is a line of natural looking, soft, attenuating turf surfacing perfect for playgrounds....
-
Guest Rooms
Carpet causes resistance that makes rolling much more difficult than on the aforementioned surfaces....
-
5.4.2 Transfer Support Length for M301 and M302
The purpose of a minimum length is to ensure that there is a minimum gripping surface available to support positioning and repositioning during a transfer....
-
Handrails [§405.8, §505]
Handrail Height and Clearance Handrail Continuity and Extensions Surface requirements and clearances facilitate a power grip along the length of handrails....
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
What happens when people walk under more difficult conditions?
What happens when people walk under more difficult conditions?...
