[2010 ADA Standards] 405.5 Clear Width. The clear width of a ramp run and, where handrails are provided, the clear width between handrails shall be 36 inches (915 mm) minimum....
Search Results "1991 Standards"
2010 ADA Definition
1991 Standards: From 2010 Title II Regulations section 35.104 & 2010 Title III Regulations section 36.104: Requirements set forth in the ADA Standards for Accessible Design, originally published on July 26, 1991, and republished as Appendix D to this part.
-
11B-405.5 Clear width
-
11B-405.2 Slope
[2010 ADA Standards] EXCEPTION: In existing sites, buildings, and facilities, ramps shall be permitted to have running slopes steeper than 1:12 complying with Table 405.2 where such...
-
11B-607.4 Grab bars
[2010 ADA Standards] 607.4 Grab Bars. Grab bars for bathtubs shall comply with 609 and shall be provided in accordance with 607.4.1 or 607.4.2. Exceptions: 1. Reserved....
-
Toilet Stalls [4.17]
Toilet Stalls [4.17] The standard stall in section 4.17 is wheelchair accessible....
-
§40.6 Records.
agency's file on each contract, grant, or loan involving the design, construction, or alteration of a residential structure shall include appropriate documentation indicating: (a) That the standards...
-
E202.7 Best Meets
Where ICT conforming to one or more requirements in the Revised 508 Standards is not commercially available, the agency shall procure the ICT that best meets the Revised 508 Standards consistent...
-
M101.1 Purpose
The proposed standards contain technical criteria for medical diagnostic equipment that is accessible to and usable by patients with disabilities....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position as described in its proposed standard...
-
B.3.iv - Who makes the determination that a product meets equivalent facilitation?
The vendor may assert that its product meets or exceeds the level of accessibility required by a particular standard through equivalent facilitation....
-
24.1 Q. What types of grab bars should the reinforcement be designed to accommodate and what types may be used if the builder elects to install grab bars in some units at the time of construction?
In determining what is an appropriate grab bar, builders are encouraged to look to the 1986 ANSI A117.1 standard, the standard cited in the Fair Housing Act....
-
Alterations and Additions
This guide provides an introduction to the scoping requirements that form the basis for the Department of Justice’s 2010 ADA Standards and the Department of Transportation's ADA Standards...
-
Accessibility of Airport Terminals and Facilities
The Foreign Carriers NPRM proposed a performance standard for foreign airports, since U.S. accessibility standards do not apply there....
-
11B-703.5.4 Character proportions
[2010 ADA Standards] 703.5.4 Character Proportions....
-
11B-703.2.4 Character proportions
[2010 ADA Standards] 703.2.4 Character Proportions....
-
11B-703.2.4 Character proportions
[2010 ADA Standards] 703.2.4 Character Proportions....
-
11B-703.2.5 Character height
[2010 ADA Standards] EXCEPTION: Where separate raised and visual characters with the same information are provided, raised character height shall be permitted to be ½ inch (13 mm)...
-
11B-1008.2.6 Ground surfaces
Ground surfaces must be inspected and maintained regularly to ensure continued compliance with the ASTM F 1951 standard....
-
11B-809.4.1 Subsequent bathrooms
ETA Editor's Note The requirement for an accessible shower at subsequent bathrooms prescribed by CBC 11B-809.4.1 is not required by 2010 ADA Standards....
-
11B-809.4.1 Subsequent bathrooms
ETA Editor's Note The requirement for an accessible shower at subsequent bathrooms prescribed by CBC 11B-809.4.1 is not required by 2010 ADA Standards....
-
11B-703.2.5 Character height
[2010 ADA Standards] EXCEPTION: Where separate raised and visual characters with the same information are provided, raised character height shall be permitted to be ½ inch (13 mm)...
-
1.1.4 Appendices
code shall not apply unless specifically adopted by a state agency or adopted by a local enforcing agency in compliance with Health and Safety Code Section 18901 et. seq. for Building Standards...
-
11B-703.5.4 Character proportions
[2010 ADA Standards] 703.5.4 Character Proportions....
-
11B-1008.2.6 Ground surfaces
Ground surfaces must be inspected and maintained regularly to ensure continued compliance with the ASTM F 1951 standard....
-
a. The employer's judgment
the quality or quantity of work that must be performed by a person holding a job, or be required to set lower standards for the job....