Word Fillable Form (0.8MB) Word Non-Fillable Form (0.8MB) PDF Non-Fillable Form (0.7MB)
Search Results "Grab Bar Height"
-
Fishing Facilities
-
II. DISCUSSION
The Court requested that the United States address the following questions: Under the above-described circumstances, does ADAAG 904.4.1’s exception apply such that the sales...
-
M305.2 Transfer Supports
Transfer supports shall comply with M305.2.
-
11B-903.4 Back support
To assist in transferring to the bench, consider providing grab bars on a wall adjacent to the bench, but not on the seat back....
-
11B-903.4 Back support
To assist in transferring to the bench, consider providing grab bars on a wall adjacent to the bench, but not on the seat back....
-
American Standard Cadet 1.6 gpf Right Height Elongated Pressure Assisted Toilet
Combination bowl and tank, less seat 12" (305mm) rough EverClean® Surface Elongated bowl Pressure-assisted siphon jet flush action 16-1/2" rim height...
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
1009.7.2 Riser height and tread depth
1009.7.2 Riser height and tread depth. ... Exceptions: 6. See Section 3404.1 for the replacement of existing stairways. ...
-
M305.2.2.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M305.2.2.1 shall be 15 inches (380 mm) long minimum. Transfer supports shall be positioned along 13 ½ inches...
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer...
-
Typical Transfer Techniques: Staff Assistance and Patient Lifts
Typical Transfer Techniques: Staff Assistance and Patient Lifts Some individuals will need additional assistance to get on and off an exam table, even if it lowers to 17‒19 inches...
-
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position. A 3-inch maximum obstruction is permitted at transfer...
-
5.8.2.6 Clearance Depth at Toe Height Above the Ground
5.8.2.6 Clearance Depth at Toe Height Above the Ground. The toe clearance depth should be 22 inches minimum at toe height....
-
608.6 Shower Spray Unit and Water
If an adjustable-height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars....
-
608.6 Shower Spray Unit and Water
If an adjustable-height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars....
-
Alternative Designs
Whereas the added height and side-entry features address the primary shortcomings of a traditional tub, they also create the two shortcomings of this tub....
-
Parking sign height measurement technique
502.6 says "Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign." But which floor or ground surface? The...
-
Exceptions When Conditions Do Not Permit Full Compliance
The proposed rule would have permitted exceptions to only certain provisions in the technical requirements when certain conditions do not permit full compliance. The final rule...
