In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
Search Results "Shower Seat"
Commonly Searched Documents
-
M305.2.7 Clearance (Section-by-Section Analysis)
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
5.4.10 Transfer Support Fittings Recommendations for M301 and M302 Description: To ensure safe and effective transfers, transfer supports must not rotate within their fittings...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
- BYO Recreation Inc. Accent Swing Seat
-
§ 36.302(f)(4) Notification of accessible seating locations
(4) Notification of accessible seating locations. ...
-
§ 36.406(d)(2)
(2) Facilities with more than 50 beds covered by this section that provide common use bathing facilities, shall provide at least one roll in shower with a seat that complies with the relevant...
-
APPENDIX E - SEATING PLANS FOR MODIFIED THEATERS
APPENDIX E SEATING PLANS FOR MODIFIED THEATERS...
-
Team or player seating areas. (Section-by-Section Analysis)
Section 221.2.1.4 of the 2004 ADAAG requires one or more wheelchair spaces to be provided in each team or player seating area with fixed seats, depending upon the number of seats provided...
-
Section 36.308 Seating in Assembly Areas (Section-by-Section Analysis)
Section 36.308(a)(1)(ii)(A) and (B) have been revised to provide that wheelchair and companion seats must be an integral part of the seating area, dispersed to all accessible seating levels...
-
4.21 SHOWER STALLS
[See subsections ...]
-
M305.2.1 Location (Section-by-Section Analysis)
patients in the supine, prone, or side-lying position with end transfer surfaces, M301.2.3.1 in the final rule, and all diagnostic equipment with transfer surfaces used by patients in the seated...
- SciFit PRO1000 - Seated Upper Body Machine
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
M305.2.3 Height (Section-by-Section Analysis)
In the MDE NPRM there was no specific requirement regarding the height of the transfer support, only that it be “within reach” of the patient (proposed M305.2.1). The Access Board...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.3 Transfer Sides
5.3 Transfer Sides.