Requires the Premium User plan or above.
(Login or upgrade your account!)
to keep a shoe heel or crutch tip from slipping on a walking surface under conditions likely to be found on the surface....
Search Results "Kitchen Work Surface"
Filters
Commonly Searched Documents
-
Landscape Forms Inc. Olithas Outdoor Tables and Benches
-
I. Slip Resistant Surface—Aisles, Steps, Floor Areas Where People Walk, Floor Areas in Securement Locations, Lift Platforms, Ramps
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
11B-505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (864 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
11B-505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (864 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Keep wall surfaces above handrails free of any protrusions....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
11B-505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (864 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
1014.2.1.2 Floor Height
The camp shelter floor at the entrance shall be 19 inches (485 mm) high maximum measured from the clear ground space.
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
Running Slope [1017.7.1]
Running slope, also referred to as grade, is the lengthwise slope of a trail, parallel to the direction of travel. Trails or trail segments of any length may be constructed with...
-
Recommendation of a 19" Lower Adjsutable Height as the Minimum Accessibility Standrds (Joint Report)
Recommendation of a 19" Lower Adjsutable Height as the Minimum Accessibility Standrds (Joint Report)
-
1018.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes.
-
7.4.3.1 Running Slope (Grade)
The running slope (grade) of trail segments shall comply with this section and shall be consistent over the distances cited. Trail running slope (grade) of up to 1:20 (5...
-
Slope [4.3.7]
Requirements in 4.3, while based on the expectation of level floors, apply equally to exterior sites. Where the running slope of an accessible route exceeds 5% it must be treated as...
-
Changes in Level [4.5.2]
Vertical changes in level up to ¼ inch are permitted without treatment along accessible routes. Changes in level ¼ to ½ inch must be beveled with a slope no greater than 1:2. Changes...
-
Den
Lamps wired to rocker wall switches Levers on all doors throughout the house FSC certified birdseye and quartersawn maple paneling Zoned heating on...
-
3.1.3.3 Cross Slope of Driveways
The cross slope of driveways shall not exceed 1:33 (3 percent). Exception. The cross slope of driveways may be no more than 1:20 (5 percent) where needed to ensure proper...
-
6.7 Slope
The slopes of beach access routes shall comply with 6.7.1 and 6.7.2
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
1014.2.1.2 Floor Height
The camp shelter floor at the entrance shall be 19 inches (485 mm) high maximum measured from the clear ground space.
-
1.2.5 Ramps
1.2.5 Ramps. When overall running slope and cross slope for accessible ramps are measured according to Sections 1.1.11 a recommended tolerance for these slopes is +0.5%. In the...
-
5.3.3 Transfer Sides Recommendations for M302
transfer onto the short side and the long side of the surface....