Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Ground Surface"
Filters
Commonly Searched Documents
-
11B-505.7.1 Circular cross section
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Cross Slope
Where floating piers are grounded out due to low water conditions, slope requirements would not apply....
-
D. Chapter 3: Building Blocks
Chapter 3 in the 2016 Non-Rail Vehicle Guidelines contains the technical requirements related to three areas—walking surfaces (T302), handrails, stanchions, and handholds (T303), and operable...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Reese Enterprises, Inc. PERFEC MATv * Aluminum Hinge
They offer solid footing and abrasive surfaces, and they are available in a variety of materials and colors to complement any entry area....
-
Background
Some engineered wood fiber (EWF) and chipped wood surfaces on playgrounds are difficult for those who use mobility aids, such as wheelchairs and walkers, because the surfaces are soft and...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
GameTime Music Time Playground Equipment
A plastic striker is attached to a rail above and below the instrument and when children pull the striker across the surface, it creates a fun ratchet-like sound. ...
-
M301.2.1, M302.2.1 Transfer Height
measured from the floor to the top of the transfer surface...
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
-
Technical Memorandum TM 2013-14 Dining Surfaces
dining surfaces based on TAS 201.1....
-
Triax 2000
A large tripod that can be raised to a fall height above the highest play surface on a playground. ...
-
810.3 Bus Shelters
Bus shelters shall provide a minimum clear floor or ground space complying with 305 entirely within the shelter....
-
5.2.1.1 Transfer Surface Width Recommendations for M301
5.2.1.1 Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying,...
-
Benches [1011.2]
A minimum of 36 by 48 inches of clear ground space must be provided near a bench, with one side of the clear space adjoining an ORAR or trail as applicable....
-
When is resurfacing considered to be an alteration?
triggers the requirement to add curb ramps if it involves work on a street or roadway spanning from one intersection to another, and includes overlays of additional material to the road surface...
-
Stairways [§504]
Stairways [§504] Requirements for stairways address treads and risers, surfaces, nosings, and handrails....
-
810.3 Bus Shelters
Bus shelters shall provide a minimum clear floor or ground space complying with 305 entirely within the shelter....
-
402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared...
-
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment
5.4.4.2 Transfer Support Distance from Transfer Surface for Imaging Equipment. Supports (transfer or positioning) should be located 1 ½ inches maximum from the transfer surface....
