This clearance location is around the cross section of the gripping surface (see Figure 5.4.7). NPRM Proposed Provision: Gripping surface clearance not addressed....
Search Results "Cross Slope"
-
5.4.7 Transfer Support Gripping Surface Clearance Recommendation for M301 and M302
-
1193.23(b)(3) (Advisory Guidance)
Manufacturers should consult with representatives from a cross-section of disability groups, particularly individuals whose disabilities affect hearing, vision, movement, manipulation, speech...
-
§ 38.77(b)
Handrails shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less than...
-
Appendix A to Part 37—Modifications to Standards for Accessible Transportation Facilities
Because the ADAAG has been established as a Federal consensus standard by the Access Board, the Department is not republishing the regulations in their entirety, but is adopting them by cross-reference...
-
§ 38.155(a)
Handrails shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less than...
-
1015.2 Where required
In assembly seating areas at cross aisles in accordance with Section 1029.12. Elevated facility observation station access hatches at detention facilities....
-
REFERENCES
NCHRP Project 3-78, Crossing Solutions at Roundabouts and Channelized Turn Lanes for Pedestrians with Vision Disabilities....
-
11B-1003.2.2 Boarding piers at boat launch ramps
length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section 11B-405.2 _|Slope...
-
307.3 Post-Mounted Objects
EXCEPTION: The sloping portions of handrails serving stairs and ramps shall not be required to comply with 307.3. Figure 307.3 Post-Mounted Protruding Objects...
-
Seats
The deck surface between the centerline of the seat and the pool edge cannot have a slope greater than 1:48....
-
Access to Performing Areas [4.33.5]
Aisles with slopes no steeper than 1:12 are often feasible in small and medium size assembly areas and permit accessible routes that coincide with general routes....
-
Landings [4.8.4]
Landings must be at least as wide as the ramp they serve and cannot slope more than 2% in any direction. Where ramps change direction, the landing must be at least 60 by 60 inches....
-
Vertical Clearance [§307.4]
Fixed barriers, such as guardrails, are required where the vertical clearance is less than 80” such as at open stairways and along sloped or curved walls....
-
Stairs
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
11B-1003.2.2 Boarding piers at boat launch ramps
length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section 11B-405.2 _|Slope...
-
Entrances
Entrances Problem The entrance area must be level (no level change greater than ½ inch) and should not slope steeply in any one direction....
-
1132A.4 Level floor or landing
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 1 inch (25.4 mm), provided a ramp with a maximum slope of 1:8 is permanently installed....
-
Road Roughness Analysis
(Loizos, 2008) PSD can also be evaluated in terms of roughness by plotting the PSD of elevation, PSD of slope, or vertical acceleration versus wavelength....
- Eastern Oregon Center for Independent Living (EOCIL) - Ontario, Pendleton, The Dalles, OR
- AJW Architectural Products U133 56 oz. One-Piece Liquid Soap Dispenser - Surface Mounted
- Spectrum Aquatics Gallatin Water Powered Assisted Access Lift
- Diversified Woodcrafts Forward Vision Workstation 2956K-L-ADA
- Salsbury Industries 61000 Series Single Tier 3 Wide Standard Metal Lockers
- Salsbury Industries 61000 Series Single Tier Standard Metal Lockers