This obligation includes, with respect to the provision of transportation services, compliance with the requirements of the rules of the Department of Justice concerning eligibility criteria...
Search Results "Compliance Agreement"
Filters
Commonly Searched Documents
-
§ 37.5(i)(1) Private entity-private transport
-
419.7 Accessibility
ETA Editor's Note California Building Code Chapters 5 through 8 are not adopted by the Division of the State Architect - Access Compliance (DSA-AC), and have been omitted....
-
419.7 Accessibility
ETA Editor's Note California Building Code Chapters 5 through 8 are not adopted by the Division of the State Architect - Access Compliance (DSA-AC), and have been omitted....
-
1133A.7 Knee and toe space
space, when required by Section 1133A, shall comply with Section 1138A.2 and the following: The knee and toe space shall be clear and unobstructed, or removable base cabinets in compliance...
-
11B-403.5.2 Clear width at turn
Exception: Where the clear width at the turn is 60 inches (1524 mm) minimum compliance with Section 11B-403.5.2 shall not be required....
-
Sargent 6500 Line Lever Hardware with Lockset
Cylinder: Brass, 6 pin, LA keyway standard Finishes : 3, 4, 10, 10B, 26, 26D (No Split Finish) Door Prep: ANSI A115.2 (161) Modified Minimum Stile: 4-1/2" (114mm) Certification Compliance...
-
Site Selection
You may wish to include an affirmative statement of compliance, or allocation of responsibilities between landlord and tenant, in any rental agreements or contracts you enter with meeting...
-
A. Arena Assembly Seating:
PSE shall provide at least 99 wheelchair accessible seats in The Palace in compliance with the wheelchair space requirements set forth in §802.1 of the 2010 Standards, in accordance...
-
11B-202.5 Alterations to qualified historic buildings and facilities
EXCEPTION: Where the State Historic Preservation Officer or Advisory Council on Historic Preservation determines that compliance with the requirements for accessible routes, entrances, or...
-
TRAINING
The curricula and materials used in the trainings required by these paragraphs shall be consistent with the provisions of this Agreement. 26....
-
INTRODUCTION
The document embodies an agreement to minimize the differences between the standards previously used by four agencies (the General Services Administration, the departments of Housing and...
-
General: ADA Standard Section 223.1
Section 223.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for medical care and long-term care facilities.
-
11B-707.4 Privacy
Justice considers the communication-related elements of ATMs to be auxiliary aids and services, rather than structural elements, to which the Safe Harbor allowance for elements built in compliance...
-
Evan Terry Associates
Our goal of providing this high quality service is achieved with a staff of 20 including 8 registered architects, 1 intern architect, 1 registered landscape architect, and 2 access compliance...
-
Implementation Approach and Schedule
The Interactive Travel Services Association (ITSA) opposed the phased implementation timeline and urged the Department to impose a single compliance deadline of at least 18 months after...
-
Section 35.150(b)(2) Safe harbor (Section-by-Section Analysis)
Once the compliance date is reached, such noncompliant facilities or elements must be made accessible in accordance with the 2010 Standards....
-
403.5.2 Clear Width at Turn
EXCEPTION: Where the clear width at the turn is 60 inches (1525 mm) minimum compliance with 403.5.2 shall not be required. Figure 403.5.2 Clear Width at Turn...
-
1.9.1.8 Adopting agency identification
ETA Editor's Note Sections from California Building Code Chapter 1 not adopted by Division of the State Architect - Access Compliance (DSA-AC) omitted. ...
-
11B-403.5.2 Clear width at turn
Exception: Where the clear width at the turn is 60 inches (1524 mm) minimum compliance with Section 11B-403.5.2 shall not be required. FIGURE 11B-403.5.2 CLEAR WIDTH AT TURN...
-
2. Effective Date
On March 15, 2012, compliance with the 2010 Standards will be required for new construction and alterations and barrier removal....
-
5. CONSTRUCTION TOLERANCES
CONSTRUCTION TOLERANCES: While it is always advisable to avoid design requirements that are at or near dimensional thresholds, construction tolerances may be used when evaluating the compliance...
-
Fixtures
For purposes of compliance with TAS 604.3.2, the reference to “fixture” shall mean the plumbing fixtures identified in TAS 213.3 and baby changing tables which are identified as convenience...
-
Gaps
However, if compliance with those measurements is not operationally or structurally feasible, operators may use bridge plates, ramps or other devices....
