Characters shall be ½ inch (12.7 mm) high minimum....
Search Results "Minimum Dimension"
Commonly Searched Documents
-
11B-407.4.8.1.1 Size
-
4(1)
(1) A minimum clear width of 36 inches is provided....
-
4.1.2 Accessible Sites and Exterior Facilities: New Construction
An accessible site shall meet the following minimum requirements:...
-
4.1.1 ACCESSIBLE SITES AND EXTERIOR FACILITIES: NEW CONSTRUCTION
An accessible site shall meet the following minimum requirements:...
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum....
-
§ 37.147 Considerations during FTA review
In reviewing each plan, at a minimum FTA will consider the following:...
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum....
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
-
11B-904.4 Sales and service counters
the number of existing counters at work stations or a reduction of the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum...
-
11B-233.3.1.2.5 Multi-story residential dwelling units in buildings with no elevator
In non-elevator buildings, a minimum of 10 percent but not less than one of the ground floor multi-story residential dwelling units shall be calculated using the total number of multi-story...
-
1003.3.2 Boarding Pier Clearances
Boarding piers at boat launch ramps shall provide clear pier space 60 inches (1525 mm) wide minimum and shall extend the full length of the boarding pier....
-
11B-1003.3.2 Boarding pier clearances
Boarding piers at boat launch ramps shall provide clear pier space 60 inches (1524 mm) wide minimum and shall extend the full length of the boarding pier....
-
Highest and Lowest Heights Obtained
For all of the minimum height transfers, the 75th and 95th percentiles were at the minimum transfer height possible with the station (10 inches)....
- KirbyBuilt Providence Picnic Table with Maximum Seating
- BEA Inc. High/Low Mount Boxes Bronze Bollards
-
Automatic Door Break Out Openings
The 2010 Standards at sections 404.1, 404.3, 404.3.1, and 404.3.6 require automatic doors that are part of a means of egress and that do not have standby power to have a 32-inch minimum...
-
604.8.1.4 Toe Clearance
The front partition and at least one side partition shall provide a toe clearance of 9 inches (230 mm) minimum above the finish floor and 6 inches (150 mm) deep minimum beyond the compartment-side...
-
604.7 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
11B-705.1.1.3.2
11B-705.1.1.3.2 Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces....
-
11B-705.1.1.3.2
Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces....
-
607.4.2.1 Back Wall
Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the bathtub...
-
11B-1009.2.3 Clear deck space
The space shall be 36 inches (914 mm) wide minimum and shall extend forward 48 inches (1219 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat....
-
11B-607.4.2.1 Back wall
Two grab bars shall be installed on the back wall, one located in accordance with Section 11B-609.4 and the other located 8 inches (203 mm) minimum and 10 inches (254 mm) maximum above the...
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....