to grasp them from outside the car while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp...
Search Results "Curb Ramp Width"
Filters
Commonly Searched Documents
-
§ 38.125(c)(8) Handrails
-
SafePath: Sport Floor Reducers for ADA and Disability Access
Showing Rubber Reducers for the Sport Floor Industry, Basketball Courts and ADA access. Disability access for Gym Floors. Proper installation of raised wood floors, especially in...
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48....
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48....
-
EZ Dock EZ Launch® System for Kayaks and Canoes
The EZ Launch® System is a safe and easy way to launch and dock kayaks and canoes. Great for people with disabilities, children or seniors. Users will feel confident transferring...
-
Priority 2: Access to Goods & Services
Word Fillable Form (2.5MB) Word Non-Fillable Form (2.4MB) PDF Non-Fillable Form (1.4MB)
-
M303.3.3.4 Edge Protection
Ramps with drop offs ½ inch (13 mm) or greater shall provide edge protection 2 inches (50 mm) high minimum on each side....
-
11B-604.8.1.2 Doors
Exception: When located at the side of a toilet compartment, the toilet compartment door opening shall provide a clear width of 34 inches (864 mm) minimum....
-
Employee Work Areas—Section 203.9 of the 2010 Standards, and Similar Sections
The 2010 Standards require a more limited level of access within employee work areas in ADA-covered facilities than UFAS, which requires employee work areas to be fully accessible....
-
1009.3 Stairways
In order to be considered part of an accessible means of egress, a stairway between stories shall comply with Sections 1009.3.1 through 1009.3.3. [DSA·AC & HCD 1.AC] In addition,...
-
11B-206.5.3 Transient lodging facilities
In transient lodging facilities, entrances, doors, and doorways providing user passage into and within guest rooms that are not required to provide mobility features complying with...
-
4.1.7(2)(b) Alterations to Qualified Historic Buildings and Facilities Not Subject to Section 106 of the National Historic Preservation Act
section 106 of the National Historic Preservation Act, if the entity undertaking the alterations believes that compliance with the requirements for accessible routes (exterior and interior), ramps...
-
11B-604.8.1.2 Doors
Exception: When located at the side of a toilet compartment, the toilet compartment door opening shall provide a clear width of 34 inches (864 mm) minimum....
-
11B-604.8.1.2 Doors
Exception: When located at the side of a toilet compartment, the toilet compartment door opening shall provide a clear width of 34 inches (864 mm) minimum....
-
§ 382.40a Boarding assistance for large aircraft
(b) Carriers shall, in cooperation with the airports they serve, provide boarding assistance to individuals with disabilities using mechanical lifts, ramps, or other suitable devices that...
-
Level boarding
If not using a lift or ramp to provide level boarding, the grantee must submit to FTA a demonstration of equivalent facilitation....
-
Attachment I
Rear Entrance Ramp There is no signage indicating the location of the ramp. ...
-
505.7.1 Circular Cross Section
505.7.1 Circular Cross Section. Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping sufaces shall not be...
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping surfaces shall not be...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
T502.2.2 Other Vehicles
For other non-rail vehicles, the vertical clearance at doorways shall be 56 inches (1420 mm) minimum on small non-rail vehicles and 68 inches (1725 mm) on large non-rail vehicles.
-
505.6 Gripping Surface
505.6 Gripping Surface. Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping...
