Support arm Incl. fixing kit for brick wall Basic material: Steel Surface material: Rilsan End cap: Nylon (PA) Provides firm support when you are sitting, standing, or transferring...
Search Results "Permitted Transfer"
Filters
Commonly Searched Documents
-
Pressalit Care VALUE Support Arm Fixed Height Swing Grab Bar
-
Surface Slopes
The proposed rule would have required clear ground spaces to have slopes not steeper than 1:50 in any direction, and would have permitted slopes not steeper than 1:33 when necessary for...
-
Platform Lifts in Transient Lodging Guest Rooms and Dwelling Units
The 1991 Standards, at section 4.1.3(5), exception 4, and the 2010 Standards, at sections 206.7 and 206.7.6, both limit the locations where platform lifts are permitted to be used as part...
-
1002.4.4 Clearances
Where provided, securement devices shall be permitted to overlap required clearances. 2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned. 3....
-
1002.4.4 Clearances
Where provided, securement devices shall be permitted to overlap required clearances. 2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned. 3....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
New Construction
substitute cells to be made accessible within the same facility, which would permit correctional authorities to meet their obligation by providing the required accessible features in cells...
-
11B-304.4 Door swing
Doors shall be permitted to swing into turning spaces....
-
304.4 Door Swing
Doors shall be permitted to swing into turning spaces....
-
304.4 Door Swing
Doors shall be permitted to swing into turning spaces....
-
R408.3 Open Risers
Open risers are not permitted....
-
504.3 Open Risers
Open risers are not permitted....
-
11B-304.4 Door swing
Doors shall be permitted to swing into turning spaces....
-
11B-304.4 Door swing
Doors shall be permitted to swing into turning spaces....
-
1630.16(a)
A religious corporation, association, educational institution, or society is permitted to give preference in employment to individuals of a particular religion to perform work connected...
-
Track Crossing
The proposed rule required route surfaces to be level with the rail top, but permitted a 2 ½ inch gap at the inner edge of rails to accommodate wheel flanges (1003.2.7)....
-
R406 Reach Ranges (Section-by-Section Analysis)
The requirements for reach ranges differ from the 2004 ADA and ABA Accessibility Guidelines in that forward reach over an obstruction is not permitted, and side reach over an obstruction...
-
1002.4.4 Clearances
Where provided, securement devices shall be permitted to overlap required clearances. 2. Wheelchair spaces shall be permitted to be mechanically or manually repositioned. 3....
-
M301.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
§1630.16(a) Religious entities
A religious corporation, association, educational institution, or society is permitted to give preference in employment to individuals of a particular religion to perform work connected...
-
1015.1 General
In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1015, the viewing area is permitted to comply with the provision...
-
Additions—Section 202.2 of the 2010 Standards
Because the Department is precluded from permitting the use of an alternative standard that might reduce accessibility for individuals with disabilities in housing settings without notice...
-
M302.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
11B-1002.4.4 Clearances
Exceptions: Where provided, securement devices shall be permitted to overlap required clearances....