Top loading machines shall have the door to the laundry compartment located 36 inches (914 mm) maximum above the finish floor. Front loading machines shall have the bottom of the...
Search Results "Grab Bar Height"
Commonly Searched Documents
-
11B-611.4 Height
-
11B-309.3 Height
Operable parts shall be placed within one or more of the reach ranges specified in Section 11B-308.
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception:...
-
11B-407.4.6.4.1 Height
Emergency control buttons shall have their centerlines 35 inches (889 mm) minimum above the finish floor.
-
11B-608.5.2 Standard roll-in type shower compartments
unit shall be located on the back wall of the compartment adjacent to the seat 16 inches (406 mm) minimum and 27 inches (686 mm) maximum from the seat wall; and shall be located above the grab...
-
FIGURE INDEX
and Depth of Urinals Figure 607.2 Clearance for Bathtubs Figure 607.4.1 Grab Bars for Bathtubs with Permanent Seats Figure 607.4.2 Grab Bars for Bathtubs with Removable In-Tub...
-
Seat Width Evaluation
seat was the smallest of the platform seat widths available in this study and was suitable for many participants (the 25th through 95th percentiles) for their level, highest and lowest height...
-
Corada Search Bar
I like the new Corada search bar and menu on the front page. The info boxes that appear are very helpful....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. The transfer supports shall not rotate when locked in place for patient...
-
III. CONCLUSION
For the foregoing reasons, neither Section 904.4.1 nor its exception requires clear counter space at sales and service counters subject to the ADA’s requirements.
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
-
11B-607.6 Shower spray unit and water
If an adjustable-height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars....
-
M305.2.1 Location (Section-by-Section Analysis)
The Committee explained that “transfer supports or handholds on adjustable medical equipment facilitate transfers onto a transfer surface by giving the individual something to hold or grab...
-
Conditions for Exceptions
[See subsections ...]
-
Conditions for Exceptions [1019]
The ABA Standards recognize the existence of constraints and limitations in the outdoor environment and allow for exceptions from specific provisions in the technical requirements...
-
1019.1 General
This section lists the conditions for the exceptions to specific provisions in 1011, 1013, 1014, 1015, 1016, 1017, and 1018. When an entity determines that any of the following...
-
If readily achievable modifications are being made in a single facility that has more than one restroom for each sex, should the public accommodation focus its resources on making one restroom for each sex fully accessible or should the public accommodation make some changes (e.g., lowering towel dispensers or installing grab bars) in each restroom?
., lowering towel dispensers or installing grab bars) in each restroom?...
-
II. Recommendations of Diagnostic Imaging Equipment Manufacturers on Transfer Surface Low Height
While it is ideal for transfer surfaces to be at the same height as the seat heights of mobility devices, there is evidence that independent transfers are also feasible with a seat height...
-
C. The Release Provisions Bar Claims Not Addressed And/Or Remedied In These Agreements
The Release Provisions Bar Claims Not Addressed And/Or Remedied In These Agreements The release provisions are also overbroad because they bar litigation concerning access issues that...
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.