Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
Search Results "Character Width (VMS)"
Filters
Commonly Searched Documents
-
T402.5 Surfaces
-
11B-705.1.2.5 Blended transitions
Detectable warnings at blended transitions shall be 36 inches (914 mm) in width....
-
11B-220.1.2 Two automatic teller machines or fare machines
shall comply with Sections 11B-309 _|Operable Parts|_, 11B-707.2 _|Clear Floor or Ground Space|_, 11B-707.4 _|Privacy|_, 11B-707.5 _|Speech Output|_, 11B-707.6 _|Input|_, 11B-707.7.2 _|Characters...
-
11B-411.2.1.7.1 Assignment by keypad hall call console
The display screen shall indicate the elevator assignment characters and a verbal announcement shall be made of the assigned elevator responding to the call....
-
11B-411.2.1.7.1 Assignment by keypad hall call console
The display screen shall indicate the elevator assignment characters and a verbal announcement shall be made of the assigned elevator responding to the call....
-
11B-703.1.1.2 Inspection
The inspection shall include, but not be limited to, verification that Braille dots and cells are properly spaced and the size, proportion and type of raised characters are in compliance...
-
11B-411.2.1.7.1 Assignment by keypad hall call console
The display screen shall indicate the elevator assignment characters and a verbal announcement shall be made of the assigned elevator responding to the call....
-
Door Maneuvering Clearance
The final rule includes clarification, which was partially contained in a previous footnote to Table 404.2.4.1, that maneuvering clearances "shall extend the full width of the doorway and...
-
403 Walking Surfaces
Section 403.5 includes requirements for the clear width of walking surfaces....
-
Clearance Around Base (M301.4.2 and M302.4.2)
The width of the base permitted within this clearance would be 26 inches wide maximum at the edge of the examination surface and is permitted to increase at a rate of 1 inch in width for...
-
11B-812.6 Vehicle spaces
All vehicle spaces shall be marked to define their width. Exceptions: 1....
-
11B-812.6 Vehicle spaces
All vehicle spaces shall be marked to define their width....
-
Circulation and flow
., N.W. does not have directional signage to the exterior accessible Café entrance and the characters of the signage on the accessible Café entry door on 9th St., N.W. do not contrast with...
-
§ 37.107(c)
(c) Compliance with paragraph (b) of this section is not required to the extent that it would significantly alter the historic or antiquated character of a historic or antiquated rail passenger...
-
5.8.1.1 Clear Platform Size
The platform should be a minimum clear width of 32-inches and a minimum clear length of 40-inches....
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
11B-705.1.2.5 Hazardous vehicular areas
Detectable warnings at hazardous vehicular areas shall be 36 inches (914 mm) in width....
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
1010.1.7 Door arrangement
Space between two doors in a series shall be 48 inches (1219 mm) minimum plus the width of a door swinging into the space....
-
Accessibility - Flatness and Lippage
Setting Bed Materials Joint Widths Construction Tolerances Sand setting beds for concrete pavers and paving slabs Joint width between adjacent units (See Figure...
-
Symmetry Vertical Platform Lift VPC-EL
A cost-effective solution, platform lifts create convenient access without compromising architectural character, Designed for ease of installation, Symmetry platform lifts are equipped with...
