A play structure made up of one or more play components where the user enters a fully enclosed play environment that utilizes pliable materials, such as plastic, netting, or fabric....
Search Results "Single Occupant Structure"
-
106.5.62 Soft Contained Play Structure
-
M305.2.2 Structural Strength
Transfer supports and their connections shall be capable of resisting vertical and horizontal forces of 250 pounds (1,112 N) applied at all points on the transfer support.
-
Structural Impracticability (Preamble, Section-by-Section Analysis)
Structural Impracticability Proposed § 36.401(c) is included in the final rule with minor changes....
-
610.4 Structural Strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
610.4 Structural Strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
Sec.36.401(c) Exception for structural impracticability
(c) Exception for structural impracticability....
-
III-7.3120 Temporary structures
III−7.3120 Temporary structures (ADAAG §4.1.1(4)). Temporary buildings that are extensively used or are essential for public use are covered....
-
11B-610.4 Structural strength
11B-610.4 Structural strength....
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—in-swinging doors (Req. # 32)
For the water closet clearance in single-user toilet rooms with the in-swinging door requirement (Req. #32), the expert panel determined that the primary beneficiaries would be persons who...
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—in-swinging doors (Req. # 32)
For the water closet clearance in single-user toilet rooms with the in-swinging door requirement (Req. #32), the expert panel determined that the primary beneficiaries would be persons who...
-
Structural Impracticability (Section-By-Section Analysis and Response to Comments)
Structural Impracticability (Section-By-Section Analysis and Response to Comments) Proposed Sec.36.401(c) is included in the final rule with minor changes....
-
§104.23(c)(3)
(3) This section does not require recipients to make building alterations that have little likelihood of being accomplished without removing or altering a load-bearing structural member....
-
4.1.1(4) Temporary Structures
(4) Temporary Structures. These guidelines cover temporary buildings or facilities as well as permanent facilities....
-
11B-610.4 Structural strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
11B-610.4 Structural strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
Homemods.org
Home modification refers to converting or adapting the environment in order to make performing tasks easier, reduce accidents, and support independent living. Home modification,...
-
State and Local Government Facilities: Guidance on the Revisions to 28 CFR Section 35.151
has added a new section, designated as Sec. 35.151(a)(2), to provide that full compliance with the requirements of this section is not required where an entity can demonstrate that it is structurally...
-
5.4.11 Transfer Support Structural Strength for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.11 Transfer Support Structural Strength for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
§ 35.151(a)(2) Exception for structural impracticability
(2) Exception for structural impracticability....
-
§100.305(d)
(d) Newly constructed housing for first occupancy after March 12, 1989 need not comply with the requirements of this section until at least 25 percent of the units are occupied....
-
1018.3 Aisles in Groups B and M
In Group B and M occupancies, the minimum clear aisle width shall be determined by Section 1005.1 for the occupant load served, but shall be not less than that required for corridors by...
-
1017.3 Aisles in Groups B and M
In Group B and M occupancies, the minimum clear aisle width shall be determined by Section 1005.1 for the occupant load served, but shall not be less than 36 inches (914 mm)....
-
1018.3 Aisles in Groups B and M
In Group B and M occupancies, the minimum clear aisle width shall be determined by Section 1005.1 for the occupant load served, but shall not be less than that required for corridors by...
-
1018.5 Aisles in other than assembly spaces and Groups B and M
In other than rooms or spaces used for assembly purposes and Group B and M occupancies, the minimum clear aisle capacity shall be determined by Section 1005.1 for the occupant load served...