Where provided, curb ramp flares shall not be steeper than 1:10.
Search Results "Side Transfer"
Filters
Commonly Searched Documents
-
406.3 Sides of Curb Ramps
-
11B-1002.5.2 Transfer height
The height of amusement ride seats designed for transfer shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
11B-1008.4.5 Transfer supports
Where play components require transfer to entry points or seats, at least one means of support for transferring shall be provided....
-
11B-1008.4.5 Transfer supports
Where play components require transfer to entry points or seats, at least one means of support for transferring shall be provided....
-
11B-1008.4.5 Transfer supports
Where play components require transfer to entry points or seats, at least one means of support for transferring shall be provided....
-
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Transfer Supports
Transfer Supports A means of support is required when transferring into the entry or seat of a play component....
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment....
-
How To Transfer from a Wheelchair to Hospital Bed (Stretcher) with a Sliding Board
Requires the Registered User plan or above. Login! -
5.2.1.4 Transfer Surface Size for Imaging Equipment
5.2.1.4 Transfer Surface Size for Imaging Equipment. The transfer surface should be 28 inches wide minimum and 21 inches deep minimum....
-
Transfer Steps
Transfer Steps Transfer steps are level surfaces in a composite structure that can be used for transferring from different levels to access play components....
-
R406.3 Unobstructed Side Reach
R406.3 Unobstructed Side Reach....
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
5.4.5.1 Transfer and Positioning Support Position for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position for Imaging Equipment....
-
M102.1 Defined Terms (Section-by-Section Analysis)
However, the Access Board has decided to add six additional terms to this section; end transfer surface, examination chair, imagining [sic] equipment with bores, imagining [sic] bed, side...
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
11B-1002.5 Amusement ride seats designed for transfer
Advisory 11B-1002.5 Amusement ride seats designed for transfer....
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Obstructed High Reach: ADA Standard Section 308.3.2
Section 308.3.2 covers the current ADA Standards for obstructed high side reach.
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
When patients transfer on the long side, table depth may be equal to the transfer surface depth....
-
Transfer Demonstration from Wheelchair to Bed and Back to Wheelchair
Requires the Registered User plan or above. Login!
-
4.7.5 SIDES OF CURB RAMPS
If a curb ramp is located where pedestrians must walk across the ramp, or where it is not protected by handrails or guardrails, then it shall have flared sides; the maximum slope of the...