Signs covered by this requirement shall, to the maximum extent practicable, be placed in uniform locations within the system....
Search Results "Maximum Dimension"
Filters
Commonly Searched Documents
-
Routes and Destinations: ADA Standard Section 810.6.2
-
11B-810.6.2 Routes and destinations
Signs covered by this requirement shall, to the maximum extent practicable, be placed in uniform locations within the system....
-
R302.5.4 Physical Constraints
R302.5.4 Physical Constraints. Where compliance with R302.5.1 or R302.5.2 is not practicable due to existing terrain or infrastructure, right-of-way availability, a notable natural...
-
Special Technical Provisions for Alterations to Existing Buildings and Facilities [4.1.6(3)]
Section 4.1.6(3) recognizes certain allowances where technical feasibility is encountered, such as steeper slopes for short ramps. Special provisions also address stairs, elevators,...
-
Side Approach and Reach
[See subsections ...]
-
Side Reach [§308.3]
The maximum reach depth for this range is 10” measured from the available clear floor space....
-
§ 35.151(b)(3)
(3) Alterations to historic properties shall comply, to the maximum extent feasible, with the provisions applicable to historic properties in the design standards specified in § 35.151(c...
-
M201.2 General Exception
Diagnostic equipment subject to M201.2 shall comply to the maximum extent practicable....
-
Chapter M1 Application and Administration
[See subsections ...]
-
4.1.6(1)(j) EXCEPTION
(j) EXCEPTION: In alteration work, if compliance with 4.1.6 is technically infeasible, the alteration shall provide accessibility to the maximum extent feasible....
-
M201.2 General Exception (Section-by-Section Analysis)
Any equipment falling under this exception must comply with the provision(s) in question to the maximum extent practicable, and must fully comply with all other provisions not utilizing...
-
Section 35.151(b)(3) Alterations to historic facilities (Section-by-Section Analysis)
Currently, the regulation provides that alterations to historic facilities shall comply to the maximum extent feasible with section 4.1.7 of UFAS or section 4.1.7 of the 1991 Standards....
-
1. General Exception
Section 510 of the Rehabilitation Act requires the MDE Standards to provide independent access “to the maximum extent possible.”...
-
Minimum Required Depth: ADA Standard Section 306.2.3
Section 306.2.3 covers the current ADA Standards for the minimum required depth for toe clearance.
-
CASI California Survey Reports Acceptance Criteria - Construction and Manufacturing Tolerances AC 02-12
Dimensions that are not stated as "maximum" or "minimum" are absolute. 11B-104.1.1 Construction and Manufacturing Tolerances....
-
Alterations: Alternate Stalls
Wheelchair maneuvering and transfer can be very difficult or impossible within these dimensions which is why these designs are permitted only in alterations where "technical infeasibility...
-
Alterations Affecting Primary Function Areas: ADA Standard Section 202.4
Section 202.4 covers the most current ADA Standards for alterations affecting primary function area.
-
(1)(a)
Permanently installed fixtures may overlap this area a maximum of 6 inches (150 mm), if the lowest portion of the fixture is a minimum of 9 inches (230 mm) above the floor, and may overlap...
-
§40.3(a)
If the design of a structure commenced prior to that date, the standards shall be made applicable to the maximum extent practicable, as determined by the head of the department, agency,...
-
Exception [1013.1, Exception]
When a condition for exception does not permit full compliance with a specific provision in the technical requirements for tent pads and tent platforms, the tent pads and tent...
-
How is “technical infeasibility” determined in an alteration?
Determining “technical infeasibility” requires a site-specific assessment of constraints or complications in relation to the planned scope of work. The term, as defined in the...
-
Side Approach
Side Approach The maximum reach depth for a high (54 inch maximum) reach is 10 inches, measured from the clear floor space....
-
11B-308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side...