Diagnostic equipment that supports patients in a supine, prone, or side-lying position shall comply with M301. ...
Search Results "Vertical Standing Support"
Filters
Commonly Searched Documents
-
M301.1 General
-
4.26.3(4)
a direct tension force of 250 lbf (1112N) plus the maximum moment from the application of 250 lbf (1112N) shall be less than the allowable withdrawal load between the fastener and the supporting...
-
5.8.2.4 Unobstructed Floor Space Recommendation
The base support affects how close the patient can get to the mammography machine because it intrudes into the floor space....
-
Toe Clearance: ADA Standard Section 604.8.1.4
Section 604.8.1.4 covers the current ADA Standards for toe clearance at wheelchair accessible compartments.
-
E207.1 General
EXCEPTION: Software that is assistive technology and that supports the accessibility services of the platform shall not be required to conform to the requirements in Chapter 5....
-
601.1 Scope (Section-by-Section Analysis)
601.1 Scope (Section-by-Section Analysis) This section proposes that the technical requirements for support documentation and services in this chapter be applied where either (a) required...
-
HEWI Life System Fixed Rectangular Mirror
A continuous mirror, which extends to the edge of the washbasin, is not only suitable for seated users but also for those standing....
-
Research Issues
NIH Mission As you all probably know, much of the biomedical research in the United States is supported by the NIH....
-
Temporay Concert Accessibility
The question that has arisen about how to address access to the open ground area in front of the stage where patrons stand – they are thinking of laying down some “mats” that would provide...
-
Reach Range
called attention to certain types of doors that, when fully open, cannot easily meet this specification, such as dishwasher doors and doors of ovens and broilers that are part of free-standing...
-
307.3 Post-Mounted Objects
Free-standing objects mounted on posts or pylons shall overhang circulation paths 12 inches (305 mm) maximum when located 27 inches (685 mm) minimum and 80 inches (2030 mm) maximum above...
-
The ADA Standards for Accessible Design (the ADA Standards)
ADAAG stands for the Americans with Disabilities Act Accessibility Guidelines, which are issued by the United States Architectural and Transportation Barriers Compliance Board (called the...
-
4.4.1* General
Free-standing objects mounted on posts or pylons may overhang 12 in (305 mm) maximum from 27 in to 80 in (685 mm to 2030 mm) above the ground or finished floor (see Fig. 8(c) and (d))....
-
Mirrors [4.19.6]
Tilted mirrors, though not prohibited, are not recommended because they give a distorted image to a person seated in a wheelchair and cannot be used by a standing person....
-
Seton Outdoor Aluminum Braille Signs - Restroom - 56363
Perfect for meeting ADA requirements in outdoor applications 6"W x 8"H Braille signs are constructed of 1/16" thick aluminum and are made to with-stand outdoor environments Raised...
-
Alterations to cells. (Section-by-Section Analysis)
Only one commenter expressed support for Option I, and a handful of commenters supported Option III. The comments on each option are discussed below....
-
ASME
Lifts are classified as: vertical platform lifts, inclined platform lifts, inclined stairway chairlifts, private residence vertical platform lifts, private residence inclined platform lifts...
-
B.
Cases concerning standing, like Newport News, and the normal rules of construction govern here....
-
Stages.
If the witness stand is raised, then either a ramp or lift must be provided to ensure access to the witness stand. ...
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2½ inches (64 mm) minimum measured along the vertical centerline of the element....
-
11B-1002.4.4 Clearances
Wheelchair spaces shall not be required to comply with Section 11B-307.4 _|Vertical Clearance|_. [2010 ADAS] Advisory 1002.4.4 Clearances Exception 3. ...
-
Gaps
spaces are provided on amusement rides, the floors of rides must be coordinated with the floors of the load and unload areas so that when the ride is at the load and unload position, the vertical...
-
608.7 Thresholds
In transfer type shower compartments, thresholds 1/2 inch (13 mm) high maximum shall be beveled, rounded, or vertical....
