5.4.1.1 Transfer Support Location for Stretchers. The transfer surface for stretchers should be oriented along the long side of the surface....
Search Results "Transfer Seat (Transportation)"
-
5.4.1.1 Transfer Support Location for Stretchers
-
Section 36.308 Seating in Assembly Areas (Section-by-Section Analysis)
Section 36.308 Seating in Assembly Areas (Section-by-Section Analysis) In the 1991 rule, § 36.308 covered seating obligations for public accommodations in assembly areas....
-
Addendum E: Comparison of participants tested at the National Disabled Veterans Winter Sports Clinic (NDVWSC) compared to the participants tested at the Human Engineering Research Laboratories and Hiram G. Andrews Center
At the time this addendum was composed, there were 31 participants enrolled in the phase 2 study at HERL (27 men and 4 women). This group of subjects was compared to all the...
-
Grab Bars
Grab Bars A grab bar must be provided on at least one side of each step and on the transfer platform (shown on page 16), or as a continuous grab bar serving each step and the platform...
-
4. Obstructions
Transportation entities are not required to pick up passengers with disabilities at nondesignated locations....
-
Standard Roll-In Type Shower Compartments: ADA Standard Section 608.5.2
Section 608.5.2 covers the current ADA Standards for controls in standard roll-in type shower compartments.
-
Connected Elevated Components
Connected Elevated Components When transfer systems are used, an elevated play component may connect to other elevated play components, providing an innovative, accessible route....
-
5.2.1.3 Transfer Surface Size for Stretchers
5.2.1.3 Transfer Surface Size for Stretchers. The transfer surface should be 28 inches wide minimum and 17 inches deep minimum located on both long sides of stretchers....
-
11B-608.5.2 Standard roll-in type shower compartments
) minimum and 27 inches (686 mm) maximum from the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor...
-
11B-608.5.2 Standard roll-in type shower compartments
) minimum and 27 inches (686 mm) maximum from the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor...
-
Shower Stalls [4.21]
ADAAG provides specifications for several types of shower stall designs: roll-in, transfer, and, in hotels (section 9), a combination of the two....
-
National Council on Independent Living
National Council on Independent Living MDE Minority Paper for a 17 inch low Transfer Surface Height Submitted to the U.S....
-
DOT/FTA Americans with Disabilities Act (ADA): Guidance Circular FTA C 4710.1
Department of Transportation’s implementing regulations at 49 CFR Parts 27, 37, 38, and 39....
-
12162(e)(2)(A)(ii)(II) Commuter rail
(II) Commuter rail Key stations in commuter rail transportation systems shall be made readily accessible to and usable by individuals with disabilities, including individuals who use...
-
§ 38.95(d) Mobility aid seating location
(d) Mobility aid seating location. Spaces for persons who wish to remain in their wheelchairs or mobility aids shall have a minimum clear floor space 48 inches by 30 inches....
-
T213.1 General
Seats on non-rail vehicles shall comply with T213....
-
Pre-boarding as an Option
Pre-boarding as an Option Although you are not required to pre-board, choosing to take advantage of a pre-boarding opportunity may assist you in securing a seating accommodation when...
-
608.7 Thresholds
In transfer type shower compartments, thresholds ½ inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
1009.4.1 Clear Deck Space
A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
-
11B-1009.4.1 Clear deck space
A clear deck space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
-
608.7 Thresholds
In transfer type shower compartments, thresholds ½ inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
5.4.1.1 Transfer Support Location Recommendation for Stretchers
5.4.1.1 Transfer Support Location Recommendation for Stretchers For Stretchers, the transfer surface is oriented along the long side of the surface....
-
608.7 Thresholds
In transfer type shower compartments, thresholds 1/2 inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
1009.4.1 Clear Deck Space
A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
