Types of Counters Maximum Height Minimum Length Knee Clearance (forward approach) Dining/Bars (service) 34 in 60 in required Dining/Bars...
Search Results "Ramp Length"
Filters
Commonly Searched Documents
-
Counters and Bars [5.2]
-
Selection of Variables
Selection of Variables Our own review of the ADAAG requirements, plus that of our subcontractor KRW, reveals that the single most needed anthropometric datum, by far, is arm length....
-
1133A.4, Item 1
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation....
-
1017.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1017.7.1) and cross slope (1017.7.2) of trails....
-
1133A.4, Item 1
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation....
-
References
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303. 303.1 General....
-
Test Courses & Surfaces
This “access route” was 574.2 ft (175.0 m) in length, and included two 137 ft (41.8 m) sections with grades of 4% to 5% (one uphill, one downhill), and two 30-foot (9.1 m) ramps with grades...
-
Side Transfer Surface
A transfer surface located within the length of the examination surface that allows patient transfer on two opposing sides of the examination surface....
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side....
-
6.8.1 Size
The resting interval length shall be a minimum of 60 inches (1525 mm) long by 60 inches (1525 mm) wide....
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
5.8.1.1 Clear Platform Size
The platform should be a minimum clear width of 32-inches and a minimum clear length of 40-inches....
-
1018.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes....
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
Path of Travel
(2) An accessible path of travel may consist of walks and sidewalks, curb ramps and other interior or exterior pedestrian ramps; clear floor paths through lobbies, corridors, rooms,...
-
Gaps: ADA Standard Section 1002.4.3
EXCEPTION: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
§ 36.309(b)(2)
(2) Required modifications to an examination may include changes in the length of time permitted for completion of the examination and adaptation of the manner in which the examination is...
-
Sec.36.309(b)(2)
(2) Required modifications to an examination may include changes in the length of time permitted for completion of the examination and adaptation of the manner in which the examination is...
-
1016.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1016.7.1) and cross slope (1016.7.2) of outdoor recreation access routes....
-
11B-705.1.1.4 Resiliency
Exception: Detectable warning surfaces at curb ramps, islands or cut-through medians shall not be required to comply with Section 11B-705.1.1.4....
-
Unified Facilities Guide Specifications
The straightedge is to be held in contact with the surface and moved ahead one - half of the length of the straightedge for each successive measurement....
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...