Objects projecting from walls (for example, telephones) with their leading edges between 27 in and 80 in (685 mm and 2030 mm) above the finished floor shall protrude no more than 4 in (100...
Search Results "Platform Edge"
-
4.4.1* General
-
4.7.10 Diagonal Curb Ramps
If diagonal (or corner type) curb ramps have returned curbs or other well-defined edges, such edges shall be parallel to the direction of pedestrian flow....
-
1.1.12 Ramp cross slope
Measure for overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the cross slope at these two locations...
-
Adjustable height protocol
Adjustable height protocol: From initial setup, only the height of the platform was adjusted incrementally: higher (Figure 3) and lower than the subject’s seat. ...
-
BTX Intelligent Fashion Tumo Programming Reverse Motor Direction
BTX systems have been installed in homes across the world for homeowners seeking a new edge on technology, increased security and light control, or an easier way to open and close their...
-
BraunAbility Vista 2 Wheelchair Lift for School Buses, Cutaway Buses, and Paratransit Vans
The Vista 2 Wheelchair Lift offers standard BraunAbility safety, quality, reliability, and durability in a unique stacking platform that does not block driver and passenger visibility through...
-
E2-b
Are pedestrian routes leading to or serving each of the service or activity areas free of overhead objects with the bottom edge lower than 80 inches above the floor?...
-
J. Transfer Space
If there is a lavatory in the accessible stall, is there 42" between the center of the toilet and the near edge of the adjacent lavatory to permit persons with disabilities to transfer onto...
-
A4.19.6 Mirrors
If mirrors are to be used by both ambulatory people and wheelchair users, then they must be at least 74 in (1880 mm) high at their topmost edge....
-
A4.19.6 MIRRORS
If mirrors are to be used by both ambulatory people and wheelchair users, then they must be at least 74 in (1880 mm) high at their topmost edge....
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADAS] 303.2 Vertical. ...
-
BRW1000 Bariatric Wheelchair Scale Demo
The digital BRW1000 scale features a low-profile platform with two-way integral ramps for efficient bariatric wheelchair loading....
-
R308.1.3 Common Requirements
Boarding and alighting areas and boarding platforms shall comply with R308.1.3....
-
T404.1 General
Boarding and alighting at boarding platforms in level boarding bus systems shall comply with T404....
-
WINDER
A tread with nonparallel edges....
-
704.2.1.2 Forward Approach
Where a forward approach is provided, the distance from the front edge of a counter within the telephone enclosure to the face of the telephone unit shall be 20 inches (510 mm) maximum....
-
Mirrors
Provide a mirror in the Spy City Café men's and women's toilet rooms where the bottom edge of the reflecting surface of the mirror is mounted no more than 40" above the finished floor....
-
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The gripping surfaces of the transfer support must be free of sharp or abrasive elements and have rounded edges....
-
T502.2 Doorways with Lifts, Ramps or Bridgeplates
Vertical clearance shall be measured from the inside finished edge of the door opening to the highest point of the deployed lift, ramp or bridgeplate below....
-
704.2.1.1 Parallel Approach
Where a parallel approach is provided, the distance from the edge of the telephone enclosure to the face of the telephone unit shall be 10 inches (255 mm) maximum....
-
Knee and Toe Space
The knee and toe space must be at least as deep as the reach depth measured from the leading edge of the obstruction....
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADA Standards] 303.2 Vertical....
-
WINDER
A tread with nonparallel edges....
