On diagnostic equipment containing wheelchair spaces with one entry that also serves as the exit, the length of the gripping surface of horizontal standing supports shall be equal to or...
Search Results "Surface Hazard"
Filters
Commonly Searched Documents
-
M305.3.1.2 Diagnostic Equipment Containing a Wheelchair Space
-
M301.2.2, M302.2.2 Transfer Size
This transfer surface is located on the longitudinal (long) side of the stretcher—either right or left side Rationale: Based upon full committee discussion and harmonization with Exam...
-
Clear Width [1018.4]
of beach access routes must be a minimum of 60 inches to enable people using mobility devices to pass people traveling in the opposite direction without veering off the firm and stable surface...
-
Q12: Full-depth Pavement Patching
Q12: Is full-depth pavement patching considered maintenance? A12: The answer to this question depends on the scope and location of the pavement patch. If the pavement patch work...
-
T208 Passenger Access Routes
[See subsections ...]
-
Highest and Lowest Heights Obtained
Table 9 shows the 5th, 25th, 50th, 75th, and 95th percentiles for protocols A through C. These data represent the ability of the participants in the study to complete a transfer. The...
-
B2. Slope
B2. Is the vehicle space relatively level (2% maximum slope in all directions)? Yes _____ No _____
-
2.4 Slope
 The running slope (grade) and cross slope of ORARs shall comply with section 2.4. Exception: Where an ORAR is permitted to be provided within a vehicular way, the...
-
11B-226.4 Baby changing tables
Baby changing tables shall comply with Sections 11B-309 and 11B-902. Baby changing tables when deployed shall not obstruct the required width of an accessible route except as allowed...
-
11B-226.4 Baby diaper changing station
Baby diaper changing stations shall comply with Sections 11B-309 and 11B-902. Baby diaper changing stations when deployed shall not obstruct the required width of an accessible route...
-
Height
The Access Board is considering whether 6 inches minimum and 19 inches maximum above the transfer surface would be an appropriate height for transfer supports on diagnostic equipment used...
-
Fire Rings, Grills, Fireplaces, and Wood Stoves
Ensure the fire-building surface within a fire ring is a minimum of 9 inches (230 millimeters) above the floor or ground surface....
-
5.4.3 Transfer Support Height for M301 and M302
The purpose of a minimum height is to ensure that the gripping surface is at an adequate height to facilitate positioning during a transfer....
-
(1) Adjustability: Minimum High Transfer Height
Therefore, transfer surfaces that are adjustable to a 25-inch maximum during patient transfer accommodate most patients who use mobility devices....
-
Balco FMS-A Roll-Up Floor Mat with Aluminum Frame Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
Pressalit Care Lift for Manually Height Adjustable Worktop
Requires the Premium User plan or above. (Login or upgrade your account!) -
Balco FMS-A Floor Mat with Extruded Vinyl Edge Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
Balco FMS-A Roll-Up Floor Mat Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
Clear Space Evaluation
to the right of the station allows them to use their right side as the trailing arm which carries more of the force during a transfer than does the leading arm when moving toward a new surface...
-
Transfer Sides (M301.2.3 and M302.2.3)
the surface, and that each transfer side provide unobstructed access to the transfer surface....
-
4.29.3 Detectable Warnings on Doors To Hazardous Areas
4.29.3 Detectable Warnings on Doors To Hazardous Areas. (Reserved)....
-
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
M305.2.3 Height (Section-by-Section Analysis)
explained that the manufacturers on the Committee determined that this recommendation did not conflict with the IEC 60601-2-52, which provides requirements for side rails to prevent entrapment hazards...
-
A4.32.4 Height of Tables or Counters
thickness of 1 1/2 in (38 mm) and a clearance of 1 1/2 in (38 mm) between legs and the underside of a work surface. 2This type of wheelchair arm does not interfere with the positioning...
