Federal procurement law requires that ITMs purchased by the Federal government comply with standards issued by the Access Board under Section 508 of the Rehabilitation Act of 1973, as amended...
Search Results "FTDS: Federal Trail Data Standards"
-
Automatic Teller Machines and Fare Machines: ADA Standard Section 707
-
Manual vs. Power (RMS Values)
The R2 values suggest that the data for both types of WCs the data is fairly linear. Figure 18: Seat RMS of Manual vs....
-
Seton Standard Braille Signs - Exit 31935
These 8" x 2" Braille signs clearly post important information for both the visually impaired and the sighted Available in many colors, each sign is outline engraved and crafted...
-
American Standard Home Cadet Bidet 5023.100
5023.100 For deck-mounted fitting • Vitreous china • Flushing rim and vertical cleansing spray • Integral overflow • Two bolt caps included Shown with 7391.733 Hampton...
-
Trailhead
Trailhead—A site designed and developed by the Forest Service or other Government agency, a trail association, trail maintaining club, or other cooperators to provide a staging area for...
-
§8.55(b) Compliance reports
In general, recipients should have available for the Department data showing the extent to which individuals with handicaps are beneficiaries of federally assisted programs....
-
1. Executive Summary
As discussed in the preamble to the proposed accessibility guidelines for pedestrian facilities in the public right-of- way, other federal agencies are required to adopt accessibility standards...
-
A.6 - Does Section 508, as implemented by the Access Board’s standards and the FAR, impose the same obligations on agencies and contractors?
Contractors interested in selling EIT to the Federal government are responsible for designing and manufacturing products which conform to the applicable Access Board’s technical provisions...
-
Objectives
The original development work, though targeted toward playground improvements, was eventually seen as a potential improvement for trail surfacing....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position as described in its proposed standard...
-
68.76. Standards of Conduct for the Registered Accessibility Specialist
Standards of Conduct for the Registered Accessibility Specialist....
-
B.6.ii. - If an agency determines that the acquisition of EIT that meets the applicable technical provisions of the Access Board’s standards would impose an undue burden, does it have any remaining obligations under Section 508?
The statute requires that the information and data be provided to individuals with disabilities by an alternative means of access....
-
GE® 24" Standard Clean Free-Standing Gas Range JGAS02SENSS
Features Configuration Range with Warming Drawer Ignition System Electronic Oven Cleaning Type Standard Clean Cooktop Burner...
-
Avoid These Mistakes When Buying a Thunderbolt Cable in Ireland
Ignoring Data Speed Ratings Not all thunderbolt cables perform the same....
-
6. Minimum (Low) Height Standard for Transfer Surfaces
Minimum (Low) Height Standard for Transfer Surfaces As indicated in Section 5.1.1, the MDE Advisory Committee recommends that equipment with transfer surfaces be height adjustable in...
-
Current industry standard practices resulting from this project
Current industry standard practices resulting from this project Interlocking Concrete Pavement Institute (ICPI) The ICPI, along with the Brick Industry Association and the National Concrete...
-
Washing Machines; Clothes Dryers— Sections 214.2 and 214.3 of the 2010 Standards
The 2010 Standards, however, permit either top loading or front loading machines in such facilities (Section 214.2 Washing Machines; Section 214.3 Clothes Dryers)....
-
Database Development
Provide a flexible tool for standards developers to assess the implications of decisions in a “what if” mode. 2. ...
-
1017.10 Trailhead Signs
Trail information signs at trailheads shall include the following: 1. Length of the trail or trail segment; 2. Surface type; 3. Typical and minimum tread width; 4....
-
1017.10 Trailhead Signs
Trail information signs at trailheads shall include the following: 1. Length of the trail or trail segment; 2. Surface type; 3. Typical and minimum tread width; 4....
-
Steps to Minimize Significant Economic Impacts on Small Entities
The final rule allows exemptions for an entire trail or beach access route when an entity determines that is impracticable for a trail to comply with the technical requirements for trails...
-
2010 California Standards for Accessible Design (excerpts relating to Safe Harbors only)
2010 California Standards for Accessible Design ETA Editor's Note This document contains excerpts from the 2010 California Building Code, relating to Safe Harbors, and should not...
-
Stanley QTL 200 Series Grade 2 Standard Duty Tubular Locks
And all Stanley keyed function locks come standard with our unique high security clutch feature, meaning your locks are secure even if the lock is tampered with - force on the outside won...
