ULIP Ultra-Light Inertial Profiler ULIP is a Segway based sensor and acquisition system for collecting pavement surface data for the computation of ride quality, surface texture,...
Search Results "Extended Floor Surface"
Commonly Searched Documents
- Starodub, Inc. Ultra-Light Inertial Profiler (ULIP) for Sidewalks
-
§ 38.53(d)(2) Exception
New vehicles operating in existing stations may have a floor height within plus or minus 11/2 inches of the platform height....
-
Clearances Around Gripping Surfaces
Guidelines specify the following clearances around grab bars to ensure sufficient space for a person to grasp the grab bar: 1½ inches absolute clearance between grab bars and the adjacent wall surfaces...
- Pilot Rock T300/T400 Series Round, Pedestal Table With CURVED Seats - Using Perforated Steel
-
Sinks [4.24]
Recommendations: A forward approach (specified in 4.24) provides convenient access at sinks used regularly or for extended periods of time....
- Boddingtons GrassCarpet™ Grass Protection Matting
- Pilot Rock XT Series Side Accessible Picnic Table Using Aluminum
- Pilot Rock XT Series Side Accessible Picnic Table Using Recycled Plastic
- UltraPlay Getting Started Installation Video
- AccessRec AccessMat Beach Access Mat System
-
Poured in Place Rubber
The surface cost for PIP ranged from $6.59/sq. ft. to $19.80/sq. ft. ...
-
11B-707.2 Clear floor or ground space
11B-707.2 Clear floor or ground space. A clear floor or ground space complying with Section 11B-305 shall be provided....
-
M305.2.5 Surface Hazards (Section-by-Section Analysis)
No public comments were submitted on this issue, but the MDE Advisory Committee voiced concern about surface hazards stating, “gripping surface configurations must provide an effective and...
-
11B-407.4.7.1.5 Button spacing
A minimum clear space of 3/8 inch (9.5 mm) or other suitable means of separation shall be provided between rows of control buttons.
-
Changes in Level and Horizontal Gaps
Comment. The referenced vehicle guidelines (like those of the proposed rule) permit the use of mini high platforms, car-borne or platform-mounted lifts, ramps or bridge plates, or...
-
604.3 Clearance
Clearances around water closets and in toilet compartments shall comply with 604.3.
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear...
-
604.3 Clearance
Clearances around water closets and in toilet compartments shall comply with 604.3.
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear...
-
J. Transfer Space
J. If there is a lavatory in the accessible stall, is there 42" between the center of the toilet and the near edge of the adjacent lavatory to permit persons with disabilities to...
-
604.3.1 Size
604.3.1 Size. Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular...
-
604.3 Clearance
604.3 Clearance. Clearances around water closets and in toilet compartments shall comply with 604.3.
-
Water Closet Clearances
The Department gave careful consideration to the costs and benefits of its adoption of the standards relating to water closet clearances in single-user toilet rooms. The primary...
-
11B-604.3 Clearance
Clearances around water closets and in toilet compartments shall comply with Section 11B-604.3.