length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section 11B-405.2 _|Slope...
Search Results "Cross Slope"
Commonly Searched Documents
- 
    
  
  11B-1005.1 Accessible routes
  
 - Weizel Security 826-S74 SR™ Partition Door
 - Corbin Russwin Inc. BLSS Trim Lever Handle & Lockset
 - AJW Architectural Products U591 1.6 Gallon Sanitary Napkin Disposal - Surface Mounted
 - 
    
  
  Issue 11: Good vibrations (vibrotactile indications)
  
Where mounting two APS on one pole can’t be avoided, take care to ensure that the activation of the vibration of one device doesn’t cause vibration of the device for the perpendicular crossing...
 - 
    
  
  Grab bars
  
Grab bars can have either circular or non-circular cross-sections [7]. Circular grab bars are more commonly used and were selected for testing. ...
 - 
    
  
  Clear Width [1018.4]
  
The clear width of beach access routes that are not removable can be reduced to a minimum of 48 inches at dune crossings....
 - 
    
  
  Small governmental jurisdictions affected by proposed accessibility guidelines
  
., sidewalks, pedestrian street crossings, and pedestrian signals)....
 - 
    
  
  11B-302.3 Openings
  
Clearance|_, 11B-409.4.3 _|Platform to Hoistway Clearance|_, 11B-410.4 _|Platform to Runway Clearance|_, 11B-810.5.3 _|Platform and Vehicle Floor Coordination|_ and 11B-810.10 _|Track Crossings...
 - 
    
  
  § 38.23(c)(8) Handrails
  
The handrail shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less...
 - 
    
  
  § 38.95(c)(8) Handrails
  
The handrail shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less...
 - 
    
  
  § 38.83(c)(8) Handrails
  
The handrail shall have a cross- sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have “eased” edges with corner radii of not less...
 - 
    
  
  § 38.125(c)(8) Handrails
  
The handrail shall have a cross-sectional diameter between 1 1/4 inches and 1 1/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less...
 - Armor-Tile Tactile Systems Surface Applied Systems
 - Tork Elevation® Matic® Hand Towel Roll Dispenser, Black
 - Georgia-Pacific enMotion® Automated Touchless Soap and Sanitizer Dispenser
 - 
    
  
  Suggested accessibility guidelines for exterior concrete surfaces
  
The deviation from slope or plane of formed surfaces over 10 feet (3 m) is ± 0.3% of length. This is approximately 3/8 inch in 10 feet (10 mm in 3 m)....
 - 
    
  
  11 [§ 4.7.6]
  
Built-up curb ramps should have flared sides with a slope of 10 percent or less or have edge protection and handrails on the sides....
 - 
    
  
  303.3 Beveled
  
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled....
 - 
    
  
  Accessible Routes
  
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
 - 
    
  
  Accessible Routes
  
Accessible route requirements in ADAAG address width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level, doors, egress, and areas...
 - 
    
  
  Comments from Individuals Who Are Blind or Have Low Vision (Section-by-Section Analysis)
  
member of the advisory committee that recommended the proposed guidelines, but filed a minority report recommending detectable warning surfaces should be required only on curb ramps with slopes...
 - Services for Independent Living (SIL) - Columbia, MO
 - Able South Carolina