Fixed barriers, such as guardrails, are required where the vertical clearance is less than 80” such as at open stairways and along sloped or curved walls....
Search Results "Back Wall"
-
Vertical Clearance [§307.4]
-
11B-608.4 Seats
Seats shall comply with 610 Exception: In residential dwelling units, seats shall not be required in shower compartments provided that reinforcement has been installed in walls so as...
-
[A] ALTERATION
restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls...
-
11B-608.4 Seats
Exception: In residential dwelling units, seats shall not be required in shower compartments provided that reinforcement has been installed in walls so as to permit the installation of seats...
-
Overview
The 2010 Standards establish two categories of pools: large pools with more than 300 linear feet of pool wall and smaller pools with less than 300 linear feet of wall....
-
Grab bars
Section 1009.4.5 of ADA-ABA [7] describes grab bars to be used on swimming pool, wading pool, and spa transfer walls....
-
11B-805.7 Built-in cabinets and work surfaces
California, issued Code Application Notice CAN 2-11B, dated 9/9/14, which includes the following interpretation of Section 11B-805.7: Built-in equipment consoles include recessed or wall...
-
Comparison of Single-User Toilet Room Layouts: 1A, 1B, and 1C
The size of this space is determined by the minimum width required for the water closet and lavatory between the side walls, the minimum wheelchair turning space, and the space required...
-
Swimming pools. (Section-by-Section Analysis)
proposing to add § 36.304(d)(3)(ii) to provide that, for purposes of the readily achievable barrier removal requirement, swimming pools that have at least 300 linear feet of swimming pool wall...
-
Alterations and Water Closet Clearances in Single-User Toilet Rooms With In-Swinging Doors (Section-by-Section Analysis)
Doors (Section-by-Section Analysis) The 1991 Standards allow a lavatory to be placed a minimum of 18 inches from the water closet centerline and a minimum of 36 inches from the side wall...
-
Swimming pools. (Section-by-Section Analysis)
Section 242.2 of the 2004 ADAAG states that swimming pools must provide two accessible means of entry, except that swimming pools with less than 300 linear feet of swimming pool wall are...
-
Rockwood Manufacturing Company 215L Tapered Door Pull 28"
• Back to back mounting — use BTB suffix (215BTB) when ordering two pulls back to back. • Advise if door thickness is other than 1-3⁄4". Material Size: 1-1/4" dia....
-
Rockwood Manufacturing Company 215 Tapered Door Pull 16"
• Back to back mounting — use BTB suffix (215BTB) when ordering two pulls back to back. • Advise if door thickness is other than 1-3⁄4". Material Size: 1" dia....
-
AJW Architectural Products U716 Series 16"W x 20"H Channel Frame Mirror w/ Mounted Shelf - Plate Glass Surface
All edges are turned down 1/2” with front turned back 1/2” for rigidity. #18 ga support bracket is welded to both frame and shelf, ground smooth....
-
AJW Architectural Products U700 Series 16"W x 20"H Angle Frame Mirror - Plate Glass Surface
Back: #20 ga pre-plated galvanized steel, with embossed horizontal louver mounting brackets....
-
AJW Architectural Products U705 Series 16"W x 30"H Angle Frame Mirror w/ Mounted Shelf - Plate Glass Surface
All edges are turned down 1/2” with front edge turned back 1/2” for rigidity and prevents possible injury. #18 ga support bracket is welded to both frame and shelf then ground smooth....
-
Lighthouse Guild
Drawing on more than 200 years of combined service, with histories dating back to 1914 and 1905, respectively, Lighthouse Guild’s experience is unmatched....
-
AJW Architectural Products UG2-Railing UG2X-Y108 108" Concealed Snap Flange, 1.25" Diameter, Peened Grip - Configuration Y
All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG3-A Series UG3-A12 12" Concealed Snap Flange, 1.5" Diameter Grab Bar - Configuration A
All mounting of grab bars when possible should have in wall mounting back plates. Find centerline mounting points and place bar on line making sure to be on center....
-
AJW Architectural Products UG130-A Series UG130-A12 12" Exposed Flange, 1.5" Diameter Grab Bar - Configuration A
All mounting of grab bars when possible should have in wall mounting back plates. Find centerline mounting points and place bar on line making sure to be on center....
-
AJW Architectural Products UG30-Railing UG30X-Y108 108" Concealed Set Screw Flange, 1.5" Diameter, Peened Grip - Configuration Y
All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG20-Railing UG20X-Y108 108" Concealed Set Screw Flange, 1.25" Diameter, Peened Grip - Configuration Y
All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG2-A Series UG2-A12 12" Concealed Snap Flange, 1.25" Diameter Grab Bar - Configuration A
All mounting of grab bars when possible should have in wall mounting back plates. Find centerline mounting points and place bar on line making sure to be on center....
-
AJW Architectural Products UG120-A Series UG120-A12 12" Exposed Flange, 1.25" Diameter Grab Bar - Configuration A
All mounting of grab bars when possible should have in wall mounting back plates. Find centerline mounting points and place bar on line making sure to be on center....
