Since 2005 the Museum has undertaken remedial measures and, in some instances, has installed state-of-the art technologies in the Museum to comply with the ADA....
Search Results "Measuring Instrument"
-
C. FINDINGS BY THE UNITED STATES
-
5.1 Transfer Surface Height Recommendations
The height of the transfer surface during patient transfer shall be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer surface....
-
Seat Width Evaluation
The additional platform width may also have been needed to accommodate larger individuals; however the size of the individual and seat width of the wheelchair were not measured and therefore...
-
1. Typical Issues
During an emergency, as a temporary measure, if additional accessible parking spaces are needed, a portable ramp can be provided in a parking space marked off by traffic cones to provide...
-
Clear Floor Space [4.16.2]
clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute The 18 inch dimension is measured...
-
Signage [4.6.4]
A height of at least 60 inches (measured to the bottom edge) is generally advisable (taking care not to make the sign a protruding object), although a higher height is better for signs at...
-
Mounting Location and Height [4.30.6]
Recommendation: At signs containing pictograms or other non-tactile information, this should be measured to the centerline of the raised/ Braille portion so that it is not too low (or high...
-
F. Publicity
To the extent any advertising is “in-kind,” Olympia’s compliance with this paragraph shall be measured by the fair market value of the advertising time used. ...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
Conclusion
perceive the world, in part, through pressure and movement of materials and surfaces against our skin, and we sense the instantaneous positions of our limbs as we move through, and take the measure...
-
Station 2-Three-Point Turn
At this station, active participants were asked to make a three-point turn and the width that they required was measured (figure 27)....
-
1.1.6
Specifications should include limits on how many local variations will be accepted and the methods by which accessible surfaces will be measured....
-
Identification [§216.5, §502.6]
Signs must be at least 60” high measured to the bottom edge so that they are visible while vehicles are parked in a space....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Clarification on Standard Roll-In Shower Compliance
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
5.1.1 Transfer Surface Height Adjustability Recommendation for M301 and M302
In determining these heights, project researchers measured the seat heights from underneath the buttocks at the center of the occupied seats, a spot likely to be lower than the front of...
-
Safe harbor for qualified small businesses regarding what is readily achievable. (Section-by-Section Analysis)
Advocacy groups both for individuals with disabilities and private businesses requested specific guidance on what measures were required for barrier removal. ...
-
2.1 Participant Recruitment and Sampling
Researchers at each of these sites were trained in the data collection methods and used the same measurement equipment to ensure consistency in measurement methods across sites....
-
4.3.5.3 180-degree turn around an obstacle
Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
Section 36.301 Eligibility Criteria (Preamble, Section-by-Section Analysis)
§ 36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
Section 36.301 Eligibility Criteria (Section-By-Section Analysis and Response to Comments)
Sec.36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...