Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
Search Results "Kitchen Work Surface"
-
11B-1008.2.6.2 Use zones
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
Pilot Rock APTX Full Sized Pedestal Rectangular Utility Tables
These larger utility tables provide work or prep area for several people at the same time....
-
Tread
Tread—The portion of a trail, outdoor recreation access route, or beach access route where traffic moves (for pedestrian routes, this is the walking surface)....
-
§ 38.79(a)
(a) Floor surfaces on aisles, step treads, places for standees, and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant....
-
Hologic, Inc.
Prone breast biopsy tables were considered by the “Imaging Equipment with Transfer Surfaces” sub-committee and are described in Section 4.3.2 of the full committee report....
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
Resting Intervals [1016.8]
., as flat as possible) so that all the wheels of a mobility device touch the ground surface when turning into and out of the resting interval....
-
7.4.3.2 Cross Slope
Where the surface is paved or is elevated above the natural ground, the cross slope shall not be steeper than 1:48 (2 percent). ...
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges....
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
1017.8.3 Slope
Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage....
-
Handrails Along Walkways
Handrails Along Walkways. The 1991 Standards do not contain any technical requirement for handrails provided along walkways that are not ramps. Section 403.6 of the 2010 Standards...
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run.
-
2. Methodology
[See subsections ...]
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
General: ADA Standard Section 205.1
Section 205.1 of the ADA Standards covers information on scoping requirements for operable parts in the most current ADA Standards.
-
1017.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
1017.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
A5.1 General
Dining counters (where there is no service) are typically found in small carry-out restaurants, bakeries, or coffee shops and may only be a narrow eating surface attached to a wall....
-
Section C: Exterior Route
(§303) C3 Is the route free of surface openings greater than 1/2", such as grates or holes in the pavement?...
-
Avoid the extremes of surface reflectivity and contrast (slides 11 and 13)
We don’t have to have highly reflective surfaces that will still reflect light but spread it, diffuse that light instead of pinpoint reflections....
-
Inpro Corporation JointMaster® AR Series Seal Expansion Joint Systems
Requires the Premium User plan or above. (Login or upgrade your account!)
