Reinforcement for grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm)...
Search Results "Equipment Room"
Commonly Searched Documents
-
11B-809.10.6.4 Reinforcement for grab bars
-
Sec.36.211 Maintenance of accessible features
Sec.36.211 Maintenance of accessible features.
-
M305.3.3 Fittings
Standing supports shall not rotate within their fittings.
-
M303.2.3 Depth
The depth of wheelchair spaces shall comply with M303.2.3.
-
M302.2.4 Transfer Sides
Options to transfer from a mobility device shall be provided on two adjoining sides of transfer surfaces. EXCEPTION: Options to transfer to or from a mobility device onto...
-
M305.3.3 Fittings (Section-by-Section Analysis)
The MDE NPRM proposed to prohibit standing supports from rotating in their fittings. There were no comments on this section and it was not addressed by the MDE Advisory Committee....
-
M303.2 Wheelchair spaces (Section-by-Section Analysis)
This is an introductory section.
-
5.2.3 Transfer Surface Measurement
5.2.3 Transfer Surface Measurement. The transfer surface should be measured from the center-point of each side of the transfer surface.
-
5.3.3.1 Transfer Sides for Exam Chairs with Fixed Footrests
5.3.3.1 Transfer Sides for Exam Chairs with Fixed Footrests. The 17 inch minimum depth and 21 inch minimum width should be located on both sides of examination chairs with a fixed...
-
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302 Description: The transfer surface size standard has two components: width and depth. The transfer surface...
-
5.3.3.1 Transfer Sides Recommendation for Exam Chairs with Fixed Footrests
5.3.3.1 Transfer Sides Recommendation for Exam Chairs with Fixed Footrests Some examination chairs have footrests that get in the way of entry from the foot end, such as dental...
-
C206 Support Documentation and Services
[See subsections ...]
-
§ 36.211 Maintenance of accessible features.
[See subsections ...]
-
C206 Support Documentation and Services (Section-by-Section Analysis)
C206 Support Documentation and Services (Section-by-Section Analysis) This is an introductory section.
-
D. Functional Performance Criteria and Technical Requirements (Section-by-Section Analysis)
Appendix C sets forth proposed functional performance criteria (Chapter 3) and technical requirements (Chapters 4 through 6) that are referenced by, and applied in, the Application...
-
C206 Support Documentation and Services
[See subsections ...]
-
M302.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface. Each transfer side...
-
M303.2.3 Depth
Where wheelchair spaces can be entered from the front or rear, the wheelchair space shall be 48 inches (1220 mm) deep minimum. Where wheelchair spaces can be entered only from the...
-
M303.2.2 Width
Wheelchair spaces shall be 36 inches (915 mm) wide minimum.
-
M305.3.3 Fittings
Standing supports shall not rotate within their fittings.
-
11B-809.10.4 Sufficient maneuvering space
Where doors swing into the toilet and bathing or powder rooms required to comply with Section 11B-809.10, a clear maneuvering space of 30 (762 mm) inches by 48 inches (1219 mm) minimum shall...
-
Food and Beverage Service
The Food Service: Accommodating Diners with Disabilities factsheet provides both legal standards and promising practices for paths of travel, approach to dining spaces, seating,...
-
Plan 6B: 12-Foot Wide Accessible Guest Room
Plan 6B: 12-Foot Wide Accessible Guest Room This drawing shows an accessible 12-foot wide guest room with features that comply with the 2010 Standards....