Published in the Federal Register on January 9, 2017. 36 CFR Part 1195 RIN 3014-AA40 Standards for Accessible Medical Diagnostic Equipment AGENCY: Architectural and...
Search Results "Character Height (Raised)"
-
36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
-
3.3.7 Toe Clearance Height, minimum
3.3.7 Toe Clearance Height, minimum There is relatively large disparity between the standards for toe clearance height, with the U.S. having the lowest (230 mm or 9 in.), followed by...
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces....
-
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT Many medical examination rooms are equipped with fixed height examination tables, with a typical 32-inch seat height....
-
Pictogram Field: ADA Standard Section 703.6.1
Pictograms shall have a field height of 6 inches (150 mm) minimum. Characters and braille shall not be located in the pictogram field....
-
Accessible Medical Equipment
Are height adjustable with a minimum of 17-19 inches from the floor to the top of the cushion? D.2....
-
Signs
A, “ADA Standards for Accessible Design,” (Standards) § 4.1.3(16)(a): Raised and Braille letters or numbers (Standards § 4.30.4); Mounting location (§ 4.30.6); Color...
-
3.3.6 Knee Clearance Height, minimum
3.3.6 Knee Clearance Height, minimum Knee clearance heights for the four sets of standards range from 650 mm (25.6 in.) (Australia) to 700 mm (27.6 in.) (U.K.) (Figure 3‒6)....
-
11B-411.2.1.4.1.2 Identification
Buttons shall be identified by raised characters and symbols, white on a black background, complying with Section 11B-703.2 and Braille complying with Section 11B-703.3....
-
11B-411.2.1.4.1.2 Identification
Buttons shall be identified by raised characters and symbols, white on a black background, complying with Section 11B-703.2 and Braille complying with Section 11B-703.3....
-
Water Flow Height
The minimum 4 inch height is intended to allow use of cups for persons who may need to use them....
-
5.8.3.1 Breast Platform Height Recommendations
5.8.3.1 Breast Platform Height Recommendations The Committee recommends decreasing the minimum height of the top of the breast platform to 26 inches above the floor....
-
Transfer Surface Height (M301.2.1 and M302.2.1)
For many patients who use mobility devices, independent transfer is possible only if the height of the transfer surface is at or near the seat height of their mobility device....
-
11B-1002.6.2 Transfer height
The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
11B-1002.6.2 Transfer height
The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
11B-1002.6.2 Transfer height
The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
-
M305.2.8 Fittings (Section-by-Section Analysis)
The MDE NPRM proposed to require that transfer supports not rotate in their fittings (proposed M305.2.3). Five commenters addressed this provision. Four of the commenters disagreed...
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
5.4.10 Transfer Support Fittings Recommendations for M301 and M302 Description: To ensure safe and effective transfers, transfer supports must not rotate within their fittings...