The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop....
Search Results "Car Dimension"
Filters
Commonly Searched Documents
-
11B-411.4.8.2.1 Signal type
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
Wheelchairs and Other Power-Driven Mobility Devices
Such devices include Segways®, golf cars, and other devices designed to operate in non-pedestrian areas....
-
Grab Bar Cross Sections
Non-circular cross sections were to have maximum cross section dimensions of 2 inches, a perimeter dimension between 4 and 4‒11/16 inches, and edges with a c inch minimum radius....
-
2.2 Key Measurement Variables and Procedures
Body and wheelchair dimensions: Approximately 125 locations of body and wheelchair points recorded in three dimensions. 3....
-
SafePath: ADA Entry Level Landing Installation Training Video
requires more than just a ramp, it requires a level-landing, otherwise known as maneuverable clearance area, a firm and stable level surface area in front of the door designed to specific dimensions...
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
5.8.2 Knee and Toe Clearance Under Breast Platform
The overall knee and toe space should be increased to a minimum of 28 inches deep, from the initially proposed 25 inch absolute dimension; increasing the knee clearance directly underneath...
-
4.4.2 Head Room
If vertical clearance of an area adjoining an accessible route is reduced to less than 80 in (nominal dimension), a barrier to warn blind or visually-impaired persons shall be provided (...
-
4.4.2 HEAD ROOM
If vertical clearance of an area adjoining an accessible route is reduced to less than 80 in (nominal dimension), a barrier to warn blind or visually-impaired persons shall be provided (...
-
Dimensional Tolerances [3.2]
Recommendation: It is good practice to avoid specifying precisely to the maximum or minimum where possible so that achieved dimensions fall within ADAAG requirements....
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
§ 38.159(b)(2)(ii) Exception
Where the lift is designed to deploy with its long dimension parallel to the vehicle axis and which pivots into or out of the vehicle while occupied (i.e., “rotary lift”), the requirements...
-
12162(a)(2)(C)(ii)
(ii) have a restroom usable by an individual who uses a wheelchair if no restroom is provided in such car for any passenger....
-
407.4.6.3 Keypads
Car control keypads shall be in a standard telephone keypad arrangement and shall comply with 407.4.7.2....
-
11B-407.4.6.3 Keypads
Car control keypads shall be in a standard telephone keypad arrangement and shall comply with Section 11B-407.4.7.2....
-
Elevators
If elevators are altered, all cars programmed to respond to the same call control must be similarly modified (§206.6.1)....
-
11B-407.4.6.3 Keypads
Car control keypads shall be in a standard telephone keypad arrangement and shall comply with Section 11B-407.4.7.2....
-
11B-407.4.6.3 Keypads
Car control keypads shall be in a standard telephone keypad arrangement and shall comply with Section 11B-407.4.7.2....
-
Van Accessible Signage
The proposed rule removed a requirement that the access designation for van parking include the term "van accessible" to clarify that both car and van drivers can use such spaces, as was...
-
11B-409.4.3 Platform to hoistway clearance
The clearance between the car platform and the edge of any landing sill shall be 1½ inch (38 mm) maximum....
-
409.4.3 Platform to Hoistway Clearance
The clearance between the car platform and the edge of any landing sill shall be 1-½ inch (38 mm) maximum....
-
11B-409.4.3 Platform to hoistway clearance
The clearance between the car platform and the edge of any landing sill shall be 1½ inch (38 mm) maximum....
